PartsTable
Technical Data Sheet
PartsTable / COMPONENT / P/N 754-8-2-8

P/N 754-8-2-8 — Technical Data Sheet

✓ Verified by PartsTable
— · ORING SEAL
WHAT YOU NEED TO KNOW
Material determines chemical compatibility Standard durometer is 70 Shore A
Wrong material = catastrophic seal failure
PRODUCT OVERVIEW

The CLAMP,LOOP is a the manufacturer industrial component. Key specifications include diameter: 0.204 INCHES NOMINAL IN, material: RUBBER CHLOROPRENE CLASS CR CUSHION, overall_width: 0.500 INCHES NOMINAL IN, special_features: WEAPONS SYSTEM ESSENTIAL, style_designator: OFFSET MOUNT, tongue_hole_type: ROUND, UNTHREADED. This part is cataloged in the Federal Logistics Information System under NSN 5340-00-291-5347, indicating validated use in U.S.

government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels. Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
P/N 754-8-2-8
NSN: 5340-00-291-5347
FSC: 5340
CAGE: D9182 — ZF INDUSTRIEANTRIEBE WITTEN GMBH (DEU)
SPECIFICATIONS
diameter0.204 INCHES NOMINAL IN
materialRUBBER CHLOROPRENE CLASS CR CUSHION
overall_width0.500 INCHES NOMINAL IN
special_featuresWEAPONS SYSTEM ESSENTIAL
style_designatorOFFSET MOUNT
tongue_hole_typeROUND, UNTHREADED
surface_treatmentCHROMATE BAND
material_thickness0.032 INCHES NOMINAL IN
loop_inside_diameter0.485 INCHES MINIMUM AND 0.515 INCHES MAXIMUM IN
end_item_identificationMULTIPLE LAUNCH ROCKET SYSTEM (MLRS)
cushioning_environmental_protectionWEATHER RESISTANT
material_document_and_classification00-A-250/5 FED SPEC SINGLE MATERIAL RESPONSE BAND
NSN5340-00-291-5347
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: P/N 754-8-2-8 MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
MATERIAL DOCUMENT AND CLASSIFICATION: 00-A-250/5 FED SPEC SINGLE MATERIAL RESPONSE BAND
•
SURFACE TREATMENT: CHROMATE BAND
•
STYLE DESIGNATOR: OFFSET MOUNT
•
DISTANCE FROM LOOP CENTER TO TONGUE END: 0.872 INCHES NOMINAL IN
•
LOOP INSIDE DIAMETER: 0.485 INCHES MINIMUM AND 0.515 INCHES MAXIMUM IN
•
CENTER TO CENTER DISTANCE BETWEEN LOOP AND MOUNTING HOLE: 0.654 INCHES NOMINAL IN
•
DIAMETER: 0.204 INCHES NOMINAL IN
TECHNICAL CHARACTERISTICS
MATERIAL DOCUMENT AND CLASSIFICATION00-A-250/5 FED SPEC SINGLE MATERIAL RESPONSE BAND
SURFACE TREATMENTCHROMATE BAND
STYLE DESIGNATOROFFSET MOUNT
DISTANCE FROM LOOP CENTER TO TONGUE END0.872 INCHES NOMINAL IN
LOOP INSIDE DIAMETER0.485 INCHES MINIMUM AND 0.515 INCHES MAXIMUM IN
END ITEM IDENTIFICATIONMULTIPLE LAUNCH ROCKET SYSTEM (MLRS)
CENTER TO CENTER DISTANCE BETWEEN LOOP AND MOUNTING HOLE0.654 INCHES NOMINAL IN
DIAMETER0.204 INCHES NOMINAL IN
MATERIALALUMINUM ALLOY 2024 BAND
SURFACE TREATMENT DOCUMENT AND CLASSIFICATION-1L-C-5541 MIL SPEC SINGLE TREATMENT RESPONSE BAND
VERIFIED SUBSTITUTES & CROSS-REFERENCES 29
MILC8603Upgraded SuccessorGOVERNMENT REGISTRY
successor cross-reference
successor
99122Upgraded SuccessorGOVERNMENT REGISTRY
successor cross-reference
successor
MS21919G8Upgraded SuccessorGOVERNMENT REGISTRY
successor cross-reference
successor
5096D16Upgraded SuccessorGOVERNMENT REGISTRY
successor cross-reference
successor
534002989402Upgraded SuccessorGOVERNMENT REGISTRY
successor cross-reference
successor
MS21919G11Upgraded SuccessorGOVERNMENT REGISTRY
successor cross-reference
successor
LIFECYCLE
StatusCANCELLEDGOVERNMENT REGISTRY
Availability—
RoHS CompliantEAR99Not HAZMAT
Ready to buy P/N 754-8-2-8?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is P/N 754-8-2-8?
P/N 754-8-2-8 is a CLAMP,LOOP.
What parts can replace P/N 754-8-2-8?
There are 29 known substitutes for P/N 754-8-2-8: MILC8603, 99122, MS21919G8 and 26 more. Substitute compatibility should be verified for your specific system.
Is P/N 754-8-2-8 still available?
P/N 754-8-2-8 is currently cancelled.
Community Feedback
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — P/N 754-8-2-8

✓ Validated with multiple authoritative sources, including Government, OEM, and Certified sources.
PartsTable Design LLC · partstable.com
Last verified: September 2026