PartsTable
Technical Data Sheet
Download PDF

MILC24066-4 — CLIP,SPRING TENSION

✓ Government record, cited
— · ORING SEAL
PRODUCT OVERVIEW

MILC24066-4: CLIP,SPRING TENSION.

The CLIP,SPRING TENSION is a the manufacturer industrial component. Key specifications include width: 1.052 INCHES MINIMUM AND 1.072 INCHES MAXIMUM IN, length: 0.570 INCHES MINIMUM AND 0.610 INCHES MAXIMUM IN, material: STEEL OVERALL, hole_diameter: 0.090 INCHES MINIMUM AND 0.096 INCHES MAXIMUM IN, overall_height: 0.670 INCHES MINIMUM AND 0.710 INCHES MAXIMUM IN, mounting_method: UNTHREADED HOLE(S). This part is cataloged in the U.S.

Government catalog under NSN 5340-00-425-1380, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.

Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
MILC24066-4
NSN: 5340-00-425-1380
NIINs: 004251380, 004333597, 009195180, 010102693, 010652806, 010718477, 010721361, 010724995, 011186447, 011284299, 011324662, 011426396, 011454294, 011679319, 011879777, 012156925, 012247388, 012341490, 012854753
FSC: 5340 — Hardware, Commercial
CAGE: 81349 — MILITARY SPECIFICATIONS PROMULGATED BY MILITARY DEPARTMENTS/AGENCIES UNDER AUTHORITY OF DEFENSE STANDARDIZATION MANUAL 4120 3-M
SPECIFICATIONS
width1.052 INCHES MINIMUM AND 1.072 INCHES MAXIMUM IN
length0.570 INCHES MINIMUM AND 0.610 INCHES MAXIMUM IN
materialSTEEL OVERALL
hole_diameter0.090 INCHES MINIMUM AND 0.096 INCHES MAXIMUM IN
overall_height0.670 INCHES MINIMUM AND 0.710 INCHES MAXIMUM IN
mounting_methodUNTHREADED HOLE(S)
surface_treatmentCADMIUM AND CHROMATE OVERALL
material_thickness0.013 INCHES MINIMUM AND 0.019 INCHES MAXIMUM IN
loop/holding_dimension0.552 INCHES MINIMUM AND 0.572 INCHES MAXIMUM IN
distance_from_loop_center_to_end0.361 INCHES MINIMUM IN
material_document_and_classificationASTM A682 ASSN STD SINGLE MATERIAL RESPONSE OVERALL
surface_treatment_document_and_classificationQQ-P-416,TYPE 2,CLASS 2 FED SPEC SINGLE TREATMENT RESPONSE OVERALL
NSN5340-00-425-1380
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: MILC24066-4 MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
LENGTH: 0.790 INCHES MINIMUM AND 0.830 INCHES MAXIMUM IN
•
SURFACE TREATMENT DOCUMENT AND CLASSIFICATION: QQ-P-416,TYPE 2,CLASS 2 FED SPEC SINGLE TREATMENT RESPONSE OVERALL
•
MOUNTING METHOD: UNTHREADED HOLE(S)
•
MATERIAL DOCUMENT AND CLASSIFICATION: ASTM A682 ASSN STD SINGLE MATERIAL RESPONSE OVERALL
•
LOOP/HOLDING DIMENSION: 0.740 INCHES MINIMUM AND 0.760 INCHES MAXIMUM IN
•
MATERIAL THICKNESS: 0.025 INCHES MINIMUM AND 0.031 INCHES MAXIMUM IN
•
DISTANCE FROM LOOP CENTER TO END: 0.470 INCHES MINIMUM IN
TECHNICAL CHARACTERISTICS
OVERALL HEIGHT0.900 INCHES MINIMUM AND 0.904 INCHES MAXIMUM IN
LENGTH0.790 INCHES MINIMUM AND 0.830 INCHES MAXIMUM IN
SURFACE TREATMENT DOCUMENT AND CLASSIFICATIONQQ-P-416,TYPE 2,CLASS 2 FED SPEC SINGLE TREATMENT RESPONSE OVERALL
MOUNTING METHODUNTHREADED HOLE(S)
MATERIAL DOCUMENT AND CLASSIFICATIONASTM A682 ASSN STD SINGLE MATERIAL RESPONSE OVERALL
LOOP/HOLDING DIMENSION0.740 INCHES MINIMUM AND 0.760 INCHES MAXIMUM IN
MATERIAL THICKNESS0.025 INCHES MINIMUM AND 0.031 INCHES MAXIMUM IN
DISTANCE FROM LOOP CENTER TO END0.470 INCHES MINIMUM IN
SURFACE TREATMENTCADMIUM AND CHROMATE OVERALL
WIDTH1.990 INCHES MINIMUM AND 2.010 INCHES MAXIMUM IN
SUBSTITUTES & CROSS-REFERENCES 2
M24066/4-115Reference document
Same NSN cross-reference
Reference document — Advisory reference — outside the item-of-supply concept
NASM24066/4Reference document
Same NSN cross-reference
Reference document — Design control — primary reference
LIFECYCLE
NSN statusCancelled· U.S. Government catalog
Acquisition advice: Insurance item — stocked against contingency demandNo demilitarization required
Ready to buy MILC24066-4?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is MILC24066-4?
MILC24066-4 is a CLIP,SPRING TENSION.
What parts can replace MILC24066-4?
There are 2 known substitutes for MILC24066-4: M24066/4-115, NASM24066/4. Substitute compatibility should be verified for your specific system.
What is the NSN for MILC24066-4?
MILC24066-4 is cataloged in the U.S. Government catalog under NSN 5340-00-425-1380. This indicates validated use in U.S. government and defense supply chains.
Community Feedback
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — MILC24066-4

✓ PartsTable — the parts reference. Every fact cited to its source.
PartsTable Design LLC · partstable.com
U.S. Government catalog: edition PUBLOGDVD v12.0.0 (OCT 2026), edition date 2026-10-01, retrieved 2026-10-18.
PartsTable commercial catalog: edition Unified commercial catalog snapshot through 2026-09-28, edition date not on file, retrieved 2026-09-28.