PartsTable
Technical Data Sheet
PartsTable / COMPONENT / FF-S-107C
FF-S-107C ✓ Verified by PartsTable
— · BOLT SCREW
WHAT YOU NEED TO KNOW
Grade/class stamped on head determines strength Metric and imperial threads look similar — measure pitch
Verify thread pitch — metric != imperial
PRODUCT OVERVIEW

The SCREW,DRIVE is a the manufacturer industrial component. Key specifications include material: STEEL COMP 410 OVERALL, head_style: HEXAGON, head_height: 0.096 INCHES MINIMUM AND 0.110 INCHES MAXIMUM IN, pilot_length: 0.062 INCHES NOMINAL IN, spline_width: 0.050 INCHES NOMINAL IN, head_diameter: 0.256 INCHES MINIMUM AND 0.270 INCHES MAXIMUM IN. This product is currently in active production with full OEM support.

This part is cataloged in the Federal Logistics Information System (FLIS) under NSN 5305-00-014-3189, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.

Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
FF-S-107C
NSN: 5305-00-014-3189
FSC: 5305
CAGE: 81348 — FEDERAL SPECIFICATIONS PROMULGATED BY GENERAL SERVICES ADMINISTRATION WASHINGTON DC (USA)
SPECIFICATIONS
materialSTEEL COMP 410 OVERALL
head_styleHEXAGON
head_height0.096 INCHES MINIMUM AND 0.110 INCHES MAXIMUM IN
pilot_length0.062 INCHES NOMINAL IN
spline_width0.050 INCHES NOMINAL IN
head_diameter0.256 INCHES MINIMUM AND 0.270 INCHES MAXIMUM IN
pilot_diameter0.080 INCHES MINIMUM AND 0.083 INCHES MAXIMUM IN
fastener_length0.970 INCHES MINIMUM AND 1.030 INCHES MAXIMUM IN
countersink_angle80.0 DEGREES MINIMUM AND 82.0 DEGREES MAXIMUM
features_providedCASEHARDENED
surface_treatmentPASSIVATE OVERALL
width_between_flats0.244 INCHES MINIMUM AND 0.250 INCHES MAXIMUM IN
NSN5305-00-014-3189
COMPONENT DIAGRAM
BOLT / SCREW — THREAD VERIFICATION REQUIRED Hex HEAD LENGTH: — THREAD: — × — MATERIAL: — PN: FF-S-107C · OEM ⚠ VERIFY BEFORE ORDERING Verify thread pitch before ordering — metric (M8×1.25) ≠ imperial (5/16-18). Wrong thread = wrong part. Grade/class stamped on bolt head determines tensile strength ✓ BROKER TIP Grade/class stamped on head determines tensile strength. Grade 8 > Grade 5 > Grade 2. Always confirm head marking matches specification requirement PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
HEAD STYLE: ROUND
•
NONMACHINE NOMINAL THREAD DIAMETER: 0.164 INCHES IN
•
HEAD HEIGHT: 0.107 INCHES MINIMUM AND 0.120 INCHES MAXIMUM IN
•
HEAD DIAMETER: 0.287 INCHES MINIMUM AND 0.309 INCHES MAXIMUM IN
•
TEST DATA DOCUMENT: 81348-FF-S-107 SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.).
•
SURFACE TREATMENT: CADMIUM OR ZINC OVERALL
•
MATERIAL: STEEL OVERALL
•
NONMACHINE THREAD STYLE: GIMLET POINT (TYPE A, AB OR BA)
TECHNICAL CHARACTERISTICS (FLIS)
HEAD STYLEROUND
NONMACHINE NOMINAL THREAD DIAMETER0.164 INCHES IN
HEAD HEIGHT0.107 INCHES MINIMUM AND 0.120 INCHES MAXIMUM IN
HEAD DIAMETER0.287 INCHES MINIMUM AND 0.309 INCHES MAXIMUM IN
TEST DATA DOCUMENT81348-FF-S-107 SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.).
SURFACE TREATMENTCADMIUM OR ZINC OVERALL
MATERIALSTEEL OVERALL
NONMACHINE THREAD STYLEGIMLET POINT (TYPE A, AB OR BA)
FEATURES PROVIDEDCASEHARDENED
INTERNAL DRIVE STYLESLOT
VERIFIED SUBSTITUTES & CROSS-REFERENCES 21
FFS107TYPEASTYLE1SInterchangeable
interchangeable cross-reference
interchangeable
144701Interchangeable
interchangeable cross-reference
interchangeable
FF-S-107 TYPE ABInterchangeable
interchangeable cross-reference
interchangeable
148595Interchangeable
interchangeable cross-reference
interchangeable
32866S2Interchangeable
interchangeable cross-reference
interchangeable
FF-S-107CInterchangeable
interchangeable cross-reference
interchangeable
LIFECYCLE
StatusACTIVE
AvailabilityOEM and secondary market
RoHS CompliantEAR99Not HAZMAT
Ready to buy FF-S-107C?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is FF-S-107C?
FF-S-107C is a SCREW,DRIVE.
What parts can replace FF-S-107C?
There are 21 known substitutes for FF-S-107C: FFS107TYPEASTYLE1S, 144701, FF-S-107 TYPE AB and 18 more. Substitute compatibility should be verified for your specific system.
What is the NSN for FF-S-107C?
FF-S-107C is cataloged in the Federal Logistics Information System (FLIS) under NSN 5305-00-014-3189. This indicates validated use in U.S. government and defense supply chains.
Community Feedback
Comments (0)
No comments yet. Be the first to share what you know.
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — FF-S-107C

✓ Validated with multiple authoritative sources, including Government, OEM, and Certified sources.
PartsTable Design LLC · partstable.com
Last verified: July 2026