PartsTable
Technical Data Sheet
PartsTable / COMPONENT / 6009-161A
6009-161A ✓ Verified by PartsTable
— · ORING SEAL
WHAT YOU NEED TO KNOW
Material determines chemical compatibility Standard durometer is 70 Shore A
Wrong material = catastrophic seal failure
PRODUCT OVERVIEW

The CLIP,SPRING TENSION is a the manufacturer industrial component. Key specifications include width: 0.552 INCHES MINIMUM AND 0.572 INCHES MAXIMUM IN, length: 0.320 INCHES MINIMUM AND 0.360 INCHES MAXIMUM IN, material: STEEL OVERALL, hole_diameter: 0.090 INCHES MINIMUM AND 0.096 INCHES MAXIMUM IN, overall_height: 0.360 INCHES MINIMUM AND 0.400 INCHES MAXIMUM IN, mounting_method: UNTHREADED HOLE(S). This product is currently in active production with full OEM support.

This part is cataloged in the Federal Logistics Information System (FLIS) under NSN 5340-01-017-0416, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.

Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
6009-161A
NSN: 5340-01-017-0416
FSC: 5340
CAGE: 02703 — SIRSTEAK MACHINERY INC (USA)
SPECIFICATIONS
width0.552 INCHES MINIMUM AND 0.572 INCHES MAXIMUM IN
length0.320 INCHES MINIMUM AND 0.360 INCHES MAXIMUM IN
materialSTEEL OVERALL
hole_diameter0.090 INCHES MINIMUM AND 0.096 INCHES MAXIMUM IN
overall_height0.360 INCHES MINIMUM AND 0.400 INCHES MAXIMUM IN
mounting_methodUNTHREADED HOLE(S)
surface_treatmentCADMIUM AND CHROMATE OVERALL
material_thickness0.013 INCHES MINIMUM AND 0.019 INCHES MAXIMUM IN
special_test_featuresSPECIAL QUALITY CONTROL TESTING
loop/holding_dimension0.302 INCHES MINIMUM AND 0.322 INCHES MAXIMUM IN
departure_from_cited_designatorAS MOD BY MATERIAL WHICH MUST CONFORM TO SHIPS PARTS CONTROL CENTER SPECIAL QUALITY CONTROL PROVISIONS
distance_from_loop_center_to_end0.196 INCHES NOMINAL IN
NSN5340-01-017-0416
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: 6009-161A MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
DEPARTURE FROM CITED DESIGNATOR: AS MOD BY MATERIAL WHICH MUST CONFORM TO SHIPS PARTS CONTROL CENTER SPECIAL QUALITY CONTROL PROVISIONS
•
SURFACE TREATMENT: CADMIUM AND CHROMATE OVERALL
•
SPECIAL TEST FEATURES: SPECIAL QUALITY CONTROL TESTING
•
SURFACE TREATMENT DOCUMENT AND CLASSIFICATION: QQ-P-416,TYPE 2,CLASS 2 FED SPEC SINGLE TREATMENT RESPONSE OVERALL
•
MATERIAL THICKNESS: 0.013 INCHES MINIMUM AND 0.019 INCHES MAXIMUM IN
•
LENGTH: 0.320 INCHES MINIMUM AND 0.360 INCHES MAXIMUM IN
•
DISTANCE FROM LOOP CENTER TO END: 0.196 INCHES NOMINAL IN
•
MATERIAL DOCUMENT AND CLASSIFICATION: ASTM A682 ASSN STD SINGLE MATERIAL RESPONSE OVERALL
TECHNICAL CHARACTERISTICS (FLIS)
DEPARTURE FROM CITED DESIGNATORAS MOD BY MATERIAL WHICH MUST CONFORM TO SHIPS PARTS CONTROL CENTER SPECIAL QUALITY CONTROL PROVISIONS
SURFACE TREATMENTCADMIUM AND CHROMATE OVERALL
SPECIAL TEST FEATURESSPECIAL QUALITY CONTROL TESTING
SURFACE TREATMENT DOCUMENT AND CLASSIFICATIONQQ-P-416,TYPE 2,CLASS 2 FED SPEC SINGLE TREATMENT RESPONSE OVERALL
MATERIAL THICKNESS0.013 INCHES MINIMUM AND 0.019 INCHES MAXIMUM IN
LENGTH0.320 INCHES MINIMUM AND 0.360 INCHES MAXIMUM IN
DISTANCE FROM LOOP CENTER TO END0.196 INCHES NOMINAL IN
MATERIAL DOCUMENT AND CLASSIFICATIONASTM A682 ASSN STD SINGLE MATERIAL RESPONSE OVERALL
OVERALL HEIGHT0.360 INCHES MINIMUM AND 0.400 INCHES MAXIMUM IN
WIDTH0.552 INCHES MINIMUM AND 0.572 INCHES MAXIMUM IN
VERIFIED SUBSTITUTES & CROSS-REFERENCES 26
5340004861924Upgraded Successor
successor cross-reference
successor
457-5671Upgraded Successor
successor cross-reference
successor
MIL-C-24066/2Upgraded Successor
successor cross-reference
successor
416949-7Upgraded Successor
successor cross-reference
successor
139-2230-000Upgraded Successor
successor cross-reference
successor
100-200-5-10Upgraded Successor
successor cross-reference
successor
LIFECYCLE
StatusACTIVE
AvailabilityOEM and secondary market
RoHS CompliantEAR99Not HAZMAT
Ready to buy 6009-161A?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is 6009-161A?
6009-161A is a CLIP,SPRING TENSION.
What parts can replace 6009-161A?
There are 26 known substitutes for 6009-161A: 5340004861924, 457-5671, MIL-C-24066/2 and 23 more. Substitute compatibility should be verified for your specific system.
What is the NSN for 6009-161A?
6009-161A is cataloged in the Federal Logistics Information System (FLIS) under NSN 5340-01-017-0416. This indicates validated use in U.S. government and defense supply chains.
Community Feedback
Comments (0)
No comments yet. Be the first to share what you know.
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — 6009-161A

✓ Validated with multiple authoritative sources, including Government, OEM, and Certified sources.
PartsTable Design LLC · partstable.com
Last verified: July 2026