PartsTable
Technical Data Sheet
Download PDF

SA10 — RESISTOR,FIXED,WIRE WOUND,INDUCT

✓ Government record, cited
— · MRO · MRO_GENERAL
PRODUCT OVERVIEW

SA10: RESISTOR,FIXED,WIRE WOUND,INDUCT.

RESISTOR,FIXED,WIRE WOUND,INDUCT. Key specifications include radius: 1.094 INCHES NOMINAL IN, material: PLASTIC PHENOLIC, body_length: 0.344 INCHES NOMINAL IN, body_diameter: 0.094 INCHES NOMINAL IN, terminal_type: WIRE LEAD, inclosure_type: ENCAPSULATED. This part is cataloged in the U.S.

Government catalog under NSN 5340-00-232-5723, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.

Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
MRO→ MRO_GENERAL→ SA10
NSN: 5340-00-232-5723
NIINs: 002325723, 005643581, 007353487, 009525152, 010447721, 017334424, 017362648
FSC: 5340 — Hardware, Commercial
CAGE: 66289 — WISCONSIN MOTORS, LLC (USA)
SPECIFICATIONS
radius1.094 INCHES NOMINAL IN
materialPLASTIC PHENOLIC
body_length0.344 INCHES NOMINAL IN
body_diameter0.094 INCHES NOMINAL IN
terminal_typeWIRE LEAD
inclosure_typeENCAPSULATED
overall_height0.844 INCHES NOMINAL IN
overall_length65.05 MILLIMETERS NOMINAL MM
voltage_rating125.0 VOLTS NOMINAL
outside_diameter0.872 INCHES MINIMUM AND 0.878 INCHES MAXIMUM IN
overall_diameter18.35 MILLIMETERS NOMINAL MM
style_designatorAXIAL TERMINAL EACH END
NSN5340-00-232-5723
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: SA10 MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
RADIUS: 1.094 INCHES NOMINAL IN
•
OUTSIDE DIAMETER: 0.872 INCHES MINIMUM AND 0.878 INCHES MAXIMUM IN
•
STYLE DESIGNATOR: CONCAVE
•
MATERIAL THICKNESS: 0.083 INCHES NOMINAL IN
•
MATERIAL: STEEL
TECHNICAL CHARACTERISTICS
RADIUS1.094 INCHES NOMINAL IN
OUTSIDE DIAMETER0.872 INCHES MINIMUM AND 0.878 INCHES MAXIMUM IN
STYLE DESIGNATORCONCAVE
MATERIAL THICKNESS0.083 INCHES NOMINAL IN
MATERIALSTEEL
SUBSTITUTES & CROSS-REFERENCES 8
PW214Reference document
Same NSN cross-reference
Reference document — Secondary reference
50B17Reference document
Same NSN cross-reference
Reference document — Secondary reference
172540Reference document
Same NSN cross-reference
Reference document — Secondary reference
12F014Reference document
Same NSN cross-reference
Reference document — Secondary reference
47563Reference document
Same NSN cross-reference
Reference document — Secondary reference
MIL-P-20691Reference document
Same NSN cross-reference
Reference document — Identification reference
LIFECYCLE
NSN statusCancelled· U.S. Government catalog
Acquisition advice: Insurance item — stocked against contingency demandNo demilitarization required
Ready to buy SA10?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is SA10?
SA10 is a RESISTOR,FIXED,WIRE WOUND,INDUCT. It is classified as a MRO (MRO_GENERAL).
What parts can replace SA10?
There are 8 known substitutes for SA10: PW214, 50B17, 172540 and 5 more. Substitute compatibility should be verified for your specific system.
What is the NSN for SA10?
SA10 is cataloged in the U.S. Government catalog under NSN 5340-00-232-5723. This indicates validated use in U.S. government and defense supply chains.
Community Feedback
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — SA10