PartsTable
Technical Data Sheet
Download PDF

N-1-5-10 — O-RING

✓ Government record, cited
— · ORING SEAL
PRODUCT OVERVIEW

N-1-5-10: O-RING.

The O-RING is a the manufacturer industrial component. Key specifications include material: COPPER ALLOY RETAINER, construction: TWO-PIECE, outside_diameter: 1.000 INCHES NOMINAL IN, retainer_thickness: 0.438 INCHES NOMINAL IN, packing_inside_diameter: 0.625 INCHES NOMINAL IN, retainer_inside_diameter: 0.625 INCHES NOMINAL IN. This part is cataloged in the U.S.

Government catalog under NSN 5330-00-698-3184, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.

Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
N-1-5-10
NSN: 5330-00-698-3184
NIINs: 006983184, 013598772
FSC: 5330 — Packing and Gasket Materials
CAGE: 0E9N0 — DAVID BROWN HYDRAULICS INC DBA HYDRECO (USA)
SPECIFICATIONS
materialCOPPER ALLOY RETAINER
constructionTWO-PIECE
outside_diameter1.000 INCHES NOMINAL IN
retainer_thickness0.438 INCHES NOMINAL IN
packing_inside_diameter0.625 INCHES NOMINAL IN
retainer_inside_diameter0.625 INCHES NOMINAL IN
packing_ring_cross-sectional_diameter0.125 INCHES MINIMUM AND 0.188 INCHES MAXIMUM IN
NSN5330-00-698-3184
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: N-1-5-10 MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
RETAINER INSIDE DIAMETER: 0.625 INCHES NOMINAL IN
•
PACKING INSIDE DIAMETER: 0.625 INCHES NOMINAL IN
•
OUTSIDE DIAMETER: 1.000 INCHES NOMINAL IN
•
PACKING RING CROSS-SECTIONAL DIAMETER: 0.125 INCHES MINIMUM AND 0.188 INCHES MAXIMUM IN
•
RETAINER THICKNESS: 0.438 INCHES NOMINAL IN
•
MATERIAL: COPPER ALLOY RETAINER
•
CONSTRUCTION: TWO-PIECE
TECHNICAL CHARACTERISTICS
RETAINER INSIDE DIAMETER0.625 INCHES NOMINAL IN
PACKING INSIDE DIAMETER0.625 INCHES NOMINAL IN
OUTSIDE DIAMETER1.000 INCHES NOMINAL IN
PACKING RING CROSS-SECTIONAL DIAMETER0.125 INCHES MINIMUM AND 0.188 INCHES MAXIMUM IN
RETAINER THICKNESS0.438 INCHES NOMINAL IN
MATERIALCOPPER ALLOY RETAINER
CONSTRUCTIONTWO-PIECE
SUBSTITUTES & CROSS-REFERENCES 5
48860Reference document
Same NSN cross-reference
Reference document — Secondary reference
5850G5002Same NSN cross-reference
Same NSN cross-reference
Also cataloged under this NSN
XC447Reference document
Same NSN cross-reference
Reference document — Secondary reference
9022964Reference document
Same NSN cross-reference
Reference document — Secondary reference
32LN15-10Reference document
Same NSN cross-reference
Reference document — Replaced / superseded reference
LIFECYCLE
NSN statusCancelled· U.S. Government catalog
Acquisition advice: Normally procured from the manufacturer (OEM)No demilitarization required
Ready to buy N-1-5-10?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is N-1-5-10?
N-1-5-10 is a O-RING.
What parts can replace N-1-5-10?
There are 5 known substitutes for N-1-5-10: 48860, 5850G5002, XC447 and 2 more. Substitute compatibility should be verified for your specific system.
What is the NSN for N-1-5-10?
N-1-5-10 is cataloged in the U.S. Government catalog under NSN 5330-00-698-3184. This indicates validated use in U.S. government and defense supply chains.
Community Feedback
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — N-1-5-10