PartsTable
Technical Data Sheet
PartsTable / COMPONENT / MS25281-2
MS25281-2 ✓ Verified by PartsTable
— · ORING SEAL
WHAT YOU NEED TO KNOW
Material determines chemical compatibility Standard durometer is 70 Shore A
Wrong material = catastrophic seal failure
PRODUCT OVERVIEW

The CLAMP,LOOP is a the manufacturer industrial component. Key specifications include diameter: 0.2350 INCHES MINIMUM AND 0.2400 INCHES MAXIMUM IN, material: PLASTIC POLYAMIDE NYLON OVERALL, overall_width: 0.4850 INCHES MINIMUM AND 0.5150 INCHES MAXIMUM IN, style_designator: SINGLE LOOP, tongue_hole_type: ROUND, UNTHREADED, material_thickness: 0.0600 INCHES MINIMUM AND 0.0750 INCHES MAXIMUM IN. This part is cataloged in the Federal Logistics Information System (FLIS) under NSN 5340-00-753-3456, indicating validated use in U.S.

government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels. Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
MS25281-2
NSN: 5340-00-753-3456
FSC: 5340
CAGE: D9182 — ZF INDUSTRIEANTRIEBE WITTEN GMBH (DEU)
SPECIFICATIONS
diameter0.2350 INCHES MINIMUM AND 0.2400 INCHES MAXIMUM IN
materialPLASTIC POLYAMIDE NYLON OVERALL
overall_width0.4850 INCHES MINIMUM AND 0.5150 INCHES MAXIMUM IN
style_designatorSINGLE LOOP
tongue_hole_typeROUND, UNTHREADED
material_thickness0.0600 INCHES MINIMUM AND 0.0750 INCHES MAXIMUM IN
loop_inside_diameter0.1050 INCHES MINIMUM AND 0.1450 INCHES MAXIMUM IN
material_document_and_classificationMIL-W-20693, COMP. A, TY 1 MIL SPEC SINGLE MATERIAL RESPONSE OVERALL
distance_from_loop_center_to_tongue_end0.7070 INCHES NOMINAL IN
center_to_center_distance_between_loop_and_mounting_hole0.4320 INCHES MINIMUM AND 0.4820 INCHES MAXIMUM IN
NSN5340-00-753-3456
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: MS25281-2 MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
DISTANCE FROM LOOP CENTER TO TONGUE END: 0.690 INCHES NOMINAL IN
•
DIAMETER: 0.198 INCHES MINIMUM AND 0.213 INCHES MAXIMUM IN
•
MATERIAL: PLASTIC POLYHEXAMETHYLENE AMIDE OVERALL
•
LOOP INSIDE DIAMETER: 0.125 INCHES NOMINAL IN
•
MATERIAL THICKNESS: 0.060 INCHES MINIMUM AND 0.080 INCHES MAXIMUM IN
•
MATERIAL DOCUMENT AND CLASSIFICATION: ASTM D4066 ASSN STD SINGLE MATERIAL RESPONSE OVERALL
TECHNICAL CHARACTERISTICS (FLIS)
DISTANCE FROM LOOP CENTER TO TONGUE END0.690 INCHES NOMINAL IN
DIAMETER0.198 INCHES MINIMUM AND 0.213 INCHES MAXIMUM IN
MATERIALPLASTIC POLYHEXAMETHYLENE AMIDE OVERALL
OVERALL WIDTH0.495 INCHES MINIMUM AND 0.510 INCHES MAXIMUM IN
LOOP INSIDE DIAMETER0.125 INCHES NOMINAL IN
SPECIAL FEATURESCOLOR NATURAL
MATERIAL THICKNESS0.060 INCHES MINIMUM AND 0.080 INCHES MAXIMUM IN
MATERIAL DOCUMENT AND CLASSIFICATIONASTM D4066 ASSN STD SINGLE MATERIAL RESPONSE OVERALL
CENTER TO CENTER DISTANCE BETWEEN LOOP AND MOUNTING HOLE0.440 INCHES NOMINAL IN
TONGUE HOLE TYPEROUND, UNTHREADED
VERIFIED SUBSTITUTES & CROSS-REFERENCES 27
HP2NUpgraded Successor
successor cross-reference
successor
2994556-16Upgraded Successor
successor cross-reference
successor
SAE-AS25281Upgraded Successor
successor cross-reference
successor
AS23190Upgraded Successor
successor cross-reference
successor
10117455Upgraded Successor
successor cross-reference
successor
MS25281R18Upgraded Successor
successor cross-reference
successor
LIFECYCLE
StatusCANCELLED
Availability—
RoHS CompliantEAR99Not HAZMAT
Ready to buy MS25281-2?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is MS25281-2?
MS25281-2 is a CLAMP,LOOP.
What parts can replace MS25281-2?
There are 27 known substitutes for MS25281-2: HP2N, 2994556-16, SAE-AS25281 and 24 more. Substitute compatibility should be verified for your specific system.
Is MS25281-2 still available?
MS25281-2 is currently cancelled.
Community Feedback
Comments (0)
No comments yet. Be the first to share what you know.
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — MS25281-2

✓ Validated with multiple authoritative sources, including Government, OEM, and Certified sources.
PartsTable Design LLC · partstable.com
Last verified: July 2026