PartsTable
Technical Data Sheet
PartsTable / COMPONENT / MS25281-10P
MS25281-10P ✓ Verified by PartsTable
— · ORING SEAL
WHAT YOU NEED TO KNOW
Material determines chemical compatibility Standard durometer is 70 Shore A
Wrong material = catastrophic seal failure
PRODUCT OVERVIEW

The CLAMP,LOOP is a the manufacturer industrial component. Key specifications include diameter: 0.198 INCHES MINIMUM AND 0.203 INCHES MAXIMUM IN, material: PLASTIC POLYHEXAMETHYLENE AMIDE OVERALL, overall_width: 0.495 INCHES MINIMUM AND 0.510 INCHES MAXIMUM IN, style_designator: SINGLE LOOP, tongue_hole_type: ROUND, UNTHREADED, material_thickness: 0.050 INCHES MINIMUM AND 0.085 INCHES MAXIMUM IN. This part is cataloged in the Federal Logistics Information System (FLIS) under NSN 5340-00-989-3032, indicating validated use in U.S.

government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels. Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
MS25281-10P
NSN: 5340-00-989-3032
FSC: 5340
CAGE: D9182 — ZF INDUSTRIEANTRIEBE WITTEN GMBH (DEU)
SPECIFICATIONS
diameter0.198 INCHES MINIMUM AND 0.203 INCHES MAXIMUM IN
materialPLASTIC POLYHEXAMETHYLENE AMIDE OVERALL
overall_width0.495 INCHES MINIMUM AND 0.510 INCHES MAXIMUM IN
style_designatorSINGLE LOOP
tongue_hole_typeROUND, UNTHREADED
material_thickness0.050 INCHES MINIMUM AND 0.085 INCHES MAXIMUM IN
loop_inside_diameter0.625 INCHES NOMINAL IN
material_document_and_classificationASTM D4066 ASSN STD SINGLE MATERIAL RESPONSE OVERALL
distance_from_loop_center_to_tongue_end0.956 INCHES NOMINAL IN
center_to_center_distance_between_loop_and_mounting_hole0.681 INCHES MINIMUM AND 0.731 INCHES MAXIMUM IN
NSN5340-00-989-3032
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: MS25281-10P MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
TONGUE HOLE TYPE: ROUND, UNTHREADED
•
MATERIAL: PLASTIC POLYHEXAMETHYLENE AMIDE OVERALL
•
MATERIAL DOCUMENT AND CLASSIFICATION: ASTM D4066 ASSN STD SINGLE MATERIAL RESPONSE OVERALL
•
MATERIAL THICKNESS: 0.050 INCHES MINIMUM AND 0.085 INCHES MAXIMUM IN
•
LOOP INSIDE DIAMETER: 0.625 INCHES NOMINAL IN
•
DISTANCE FROM LOOP CENTER TO TONGUE END: 0.956 INCHES NOMINAL IN
•
CENTER TO CENTER DISTANCE BETWEEN LOOP AND MOUNTING HOLE: 0.681 INCHES MINIMUM AND 0.731 INCHES MAXIMUM IN
•
DIAMETER: 0.198 INCHES MINIMUM AND 0.203 INCHES MAXIMUM IN
TECHNICAL CHARACTERISTICS (FLIS)
TONGUE HOLE TYPEROUND, UNTHREADED
MATERIALPLASTIC POLYHEXAMETHYLENE AMIDE OVERALL
MATERIAL DOCUMENT AND CLASSIFICATIONASTM D4066 ASSN STD SINGLE MATERIAL RESPONSE OVERALL
MATERIAL THICKNESS0.050 INCHES MINIMUM AND 0.085 INCHES MAXIMUM IN
LOOP INSIDE DIAMETER0.625 INCHES NOMINAL IN
DISTANCE FROM LOOP CENTER TO TONGUE END0.956 INCHES NOMINAL IN
CENTER TO CENTER DISTANCE BETWEEN LOOP AND MOUNTING HOLE0.681 INCHES MINIMUM AND 0.731 INCHES MAXIMUM IN
DIAMETER0.198 INCHES MINIMUM AND 0.203 INCHES MAXIMUM IN
OVERALL WIDTH0.495 INCHES MINIMUM AND 0.510 INCHES MAXIMUM IN
STYLE DESIGNATORSINGLE LOOP
VERIFIED SUBSTITUTES & CROSS-REFERENCES 26
457-6209Upgraded Successor
successor cross-reference
successor
MS25281-F12Upgraded Successor
successor cross-reference
successor
10301187Upgraded Successor
successor cross-reference
successor
MS25281-F16Upgraded Successor
successor cross-reference
successor
SYMZ-70276 ITEM 3Upgraded Successor
successor cross-reference
successor
9M843-28Upgraded Successor
successor cross-reference
successor
LIFECYCLE
StatusCANCELLED
Availability—
RoHS CompliantEAR99Not HAZMAT
Ready to buy MS25281-10P?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is MS25281-10P?
MS25281-10P is a CLAMP,LOOP.
What parts can replace MS25281-10P?
There are 26 known substitutes for MS25281-10P: 457-6209, MS25281-F12, 10301187 and 23 more. Substitute compatibility should be verified for your specific system.
Is MS25281-10P still available?
MS25281-10P is currently cancelled.
Community Feedback
Comments (0)
No comments yet. Be the first to share what you know.
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — MS25281-10P

✓ Validated with multiple authoritative sources, including Government, OEM, and Certified sources.
PartsTable Design LLC · partstable.com
Last verified: July 2026