PartsTable
Technical Data Sheet

M24066/2-129 — CLIP,SPRING TENSION

✓ Government record, cited
— · ORING SEAL
PRODUCT OVERVIEW

M24066/2-129: CLIP,SPRING TENSION.

The CLIP,SPRING TENSION is a the manufacturer industrial component. Key specifications include width: 0.927 INCHES MINIMUM AND 0.947 INCHES MAXIMUM IN, length: 0.680 INCHES MINIMUM AND 0.720 INCHES MAXIMUM IN, material: STEEL OVERALL, hole_diameter: 0.125 INCHES MINIMUM AND 0.131 INCHES MAXIMUM IN, overall_height: 0.780 INCHES MINIMUM AND 0.820 INCHES MAXIMUM IN, surface_treatment: CADMIUM OR CADMIUM AND CHROMATE OR CADMIUM AND PHOSPHATE OVERALL. This part is cataloged in the U.S.

Government catalog under NSN 5340-01-164-0527, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.

Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
M24066/2-129
NSN: 5340-01-164-0527
FSC: 5340 — Hardware, Commercial
CAGE: 81349 — MILITARY SPECIFICATIONS PROMULGATED BY MILITARY DEPARTMENTS/AGENCIES UNDER AUTHORITY OF DEFENSE STANDARDIZATION MANUAL 4120 3-M
SPECIFICATIONS
width0.927 INCHES MINIMUM AND 0.947 INCHES MAXIMUM IN
length0.680 INCHES MINIMUM AND 0.720 INCHES MAXIMUM IN
materialSTEEL OVERALL
hole_diameter0.125 INCHES MINIMUM AND 0.131 INCHES MAXIMUM IN
overall_height0.780 INCHES MINIMUM AND 0.820 INCHES MAXIMUM IN
surface_treatmentCADMIUM OR CADMIUM AND CHROMATE OR CADMIUM AND PHOSPHATE OVERALL
material_thickness0.013 INCHES MINIMUM AND 0.019 INCHES MAXIMUM IN
loop/holding_dimension0.660 INCHES MINIMUM AND 0.680 INCHES MAXIMUM IN
distance_from_loop_center_to_end0.425 INCHES MINIMUM IN
surface_treatment_document_and_classificationQQ-P-416 FED SPEC ALL TREATMENT RESPONSES OVERALL
NSN5340-01-164-0527
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: M24066/2-129 MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
LENGTH: 0.680 INCHES MINIMUM AND 0.720 INCHES MAXIMUM IN
•
SURFACE TREATMENT DOCUMENT AND CLASSIFICATION: QQ-P-416 FED SPEC ALL TREATMENT RESPONSES OVERALL
•
LOOP/HOLDING DIMENSION: 0.660 INCHES MINIMUM AND 0.680 INCHES MAXIMUM IN
•
MATERIAL THICKNESS: 0.013 INCHES MINIMUM AND 0.019 INCHES MAXIMUM IN
•
DISTANCE FROM LOOP CENTER TO END: 0.425 INCHES MINIMUM IN
•
SURFACE TREATMENT: CADMIUM OR CADMIUM AND CHROMATE OR CADMIUM AND PHOSPHATE OVERALL
•
WIDTH: 0.927 INCHES MINIMUM AND 0.947 INCHES MAXIMUM IN
TECHNICAL CHARACTERISTICS
OVERALL HEIGHT0.780 INCHES MINIMUM AND 0.820 INCHES MAXIMUM IN
LENGTH0.680 INCHES MINIMUM AND 0.720 INCHES MAXIMUM IN
SURFACE TREATMENT DOCUMENT AND CLASSIFICATIONQQ-P-416 FED SPEC ALL TREATMENT RESPONSES OVERALL
LOOP/HOLDING DIMENSION0.660 INCHES MINIMUM AND 0.680 INCHES MAXIMUM IN
MATERIAL THICKNESS0.013 INCHES MINIMUM AND 0.019 INCHES MAXIMUM IN
DISTANCE FROM LOOP CENTER TO END0.425 INCHES MINIMUM IN
SURFACE TREATMENTCADMIUM OR CADMIUM AND CHROMATE OR CADMIUM AND PHOSPHATE OVERALL
WIDTH0.927 INCHES MINIMUM AND 0.947 INCHES MAXIMUM IN
MATERIALSTEEL OVERALL
HOLE DIAMETER0.125 INCHES MINIMUM AND 0.131 INCHES MAXIMUM IN
SUBSTITUTES & CROSS-REFERENCES 5
M24066/2-329Reference document
Same NSN cross-reference
Reference document — Secondary reference
NASM24066/2Reference document
Same NSN cross-reference
Reference document — Design control — primary reference
MIL-C-24066/2Reference document
Same NSN cross-reference
Reference document — Secondary reference
416949-29Reference document
Same NSN cross-reference
Reference document — Advisory reference — outside the item-of-supply concept
B82285Same NSN cross-reference
Same NSN cross-reference
Also cataloged under this NSN
LIFECYCLE
NSN statusActive· U.S. Government catalog
Acquisition advice: Normally procured from the manufacturer (OEM)No demilitarization required
Ready to buy M24066/2-129?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is M24066/2-129?
M24066/2-129 is a CLIP,SPRING TENSION.
What parts can replace M24066/2-129?
There are 5 known substitutes for M24066/2-129: M24066/2-329, NASM24066/2, MIL-C-24066/2 and 2 more. Substitute compatibility should be verified for your specific system.
What is the NSN for M24066/2-129?
M24066/2-129 is cataloged in the U.S. Government catalog under NSN 5340-01-164-0527. This indicates validated use in U.S. government and defense supply chains.
Community Feedback
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — M24066/2-129

✓ PartsTable — the parts reference. Every fact cited to its source.
PartsTable Design LLC · partstable.com
U.S. Government catalog: edition PUBLOGDVD v12.0.0 (OCT 2026), edition date 2026-10-01, retrieved 2026-10-18.
PartsTable commercial catalog: edition Unified commercial catalog snapshot through 2026-09-28, edition date not on file, retrieved 2026-09-28.