PartsTable
Technical Data Sheet
PartsTable / COMPONENT / AS25281
AS25281 ✓ Verified by PartsTable
— · ORING SEAL
WHAT YOU NEED TO KNOW
Material determines chemical compatibility Standard durometer is 70 Shore A
Wrong material = catastrophic seal failure
PRODUCT OVERVIEW

The CLAMP,LOOP is a the manufacturer industrial component. Key specifications include diameter: 0.198 INCHES MINIMUM AND 0.213 INCHES MAXIMUM IN, material: PLASTIC POLYHEXAMETHYLENE AMIDE OVERALL, overall_width: 0.495 INCHES MINIMUM AND 0.610 INCHES MAXIMUM IN, style_designator: SINGLE LOOP, tongue_hole_type: ROUND, UNTHREADED, material_thickness: 0.050 INCHES MINIMUM AND 0.085 INCHES MAXIMUM IN. This part is cataloged in the Federal Logistics Information System (FLIS) under NSN 5340-00-819-7408, indicating validated use in U.S.

government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels. Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
AS25281
NSN: 5340-00-819-7408
FSC: 5340
CAGE: 81343 — SOCIETY OF AUTOMOTIVE ENGINEERS INC (USA)
SPECIFICATIONS
diameter0.198 INCHES MINIMUM AND 0.213 INCHES MAXIMUM IN
materialPLASTIC POLYHEXAMETHYLENE AMIDE OVERALL
overall_width0.495 INCHES MINIMUM AND 0.610 INCHES MAXIMUM IN
style_designatorSINGLE LOOP
tongue_hole_typeROUND, UNTHREADED
material_thickness0.050 INCHES MINIMUM AND 0.085 INCHES MAXIMUM IN
loop_inside_diameter0.855 INCHES MINIMUM AND 0.895 INCHES MAXIMUM IN
special_test_featuresSPECIAL QUALITY CONTROL TESTING
departure_from_cited_designatorAS MOD BY MATERIAL WHICH MUST CONFORM TO SHIPS PARTS CONTROL CENTER SPECIAL QUALITY CONTROL PROVISIONS
material_document_and_classificationASTM D4066 ASSN STD SINGLE MATERIAL RESPONSE OVERALL
distance_from_loop_center_to_tongue_end1.093 INCHES MINIMUM AND 1.233 INCHES MAXIMUM IN
center_to_center_distance_between_loop_and_mounting_hole0.853 INCHES MINIMUM AND 0.903 INCHES MAXIMUM IN
NSN5340-00-819-7408
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: AS25281 MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
TONGUE HOLE TYPE: ROUND, UNTHREADED
•
MATERIAL: PLASTIC POLYHEXAMETHYLENE AMIDE OVERALL
•
MATERIAL DOCUMENT AND CLASSIFICATION: ASTM D4066 ASSN STD SINGLE MATERIAL RESPONSE OVERALL
•
STYLE DESIGNATOR: SINGLE LOOP
•
DISTANCE FROM LOOP CENTER TO TONGUE END: 1.268 INCHES NOMINAL IN
•
DIAMETER: 0.198 INCHES MINIMUM AND 0.213 INCHES MAXIMUM IN
•
CENTER TO CENTER DISTANCE BETWEEN LOOP AND MOUNTING HOLE: 0.983 INCHES NOMINAL IN
TECHNICAL CHARACTERISTICS (FLIS)
TONGUE HOLE TYPEROUND, UNTHREADED
OVERALL WIDTH0.495 INCHES MINIMUM AND 0.610 INCHES MAXIMUM IN
MATERIALPLASTIC POLYHEXAMETHYLENE AMIDE OVERALL
MATERIAL DOCUMENT AND CLASSIFICATIONASTM D4066 ASSN STD SINGLE MATERIAL RESPONSE OVERALL
STYLE DESIGNATORSINGLE LOOP
DISTANCE FROM LOOP CENTER TO TONGUE END1.268 INCHES NOMINAL IN
DIAMETER0.198 INCHES MINIMUM AND 0.213 INCHES MAXIMUM IN
CENTER TO CENTER DISTANCE BETWEEN LOOP AND MOUNTING HOLE0.983 INCHES NOMINAL IN
MATERIAL THICKNESS0.060 INCHES MINIMUM AND 0.130 INCHES MAXIMUM IN
SPECIAL FEATURESCOLOR NATURAL
VERIFIED SUBSTITUTES & CROSS-REFERENCES 25
SAE-AS25281Upgraded Successor
successor cross-reference
successor
10117443Upgraded Successor
successor cross-reference
successor
9M843-2Upgraded Successor
successor cross-reference
successor
HP2NUpgraded Successor
successor cross-reference
successor
2994556-16Upgraded Successor
successor cross-reference
successor
AS23190Upgraded Successor
successor cross-reference
successor
LIFECYCLE
StatusCANCELLED
Availability—
RoHS CompliantEAR99Not HAZMAT
Ready to buy AS25281?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is AS25281?
AS25281 is a CLAMP,LOOP.
What parts can replace AS25281?
There are 25 known substitutes for AS25281: SAE-AS25281, 10117443, 9M843-2 and 22 more. Substitute compatibility should be verified for your specific system.
Is AS25281 still available?
AS25281 is currently cancelled.
Community Feedback
Comments (0)
No comments yet. Be the first to share what you know.
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — AS25281

✓ Validated with multiple authoritative sources, including Government, OEM, and Certified sources.
PartsTable Design LLC · partstable.com
Last verified: July 2026