PartsTable
Technical Data Sheet
PartsTable / COMPONENT / AN6231-8
AN6231-8 ✓ Verified by PartsTable
— · ORING SEAL
WHAT YOU NEED TO KNOW
Material determines chemical compatibility Standard durometer is 70 Shore A
Wrong material = catastrophic seal failure
PRODUCT OVERVIEW

The RING,WIPER is a the manufacturer industrial component. Key specifications include ring_style: CONCENTRIC, joint_style: DIAGONAL JOINT, inside_diameter: 0.938 INCHES NOMINAL IN, outside_diameter: 1.157 INCHES NOMINAL IN, material_thickness: 0.125 INCHES NOMINAL IN, fsc_application_data: HYDRAULIC SYSTEM,ACFT. This product is currently in active production with full OEM support.

This part is cataloged in the Federal Logistics Information System (FLIS) under NSN 5330-00-580-6646, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.

Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
AN6231-8
NSN: 5330-00-580-6646
FSC: 5330
CAGE: 88044 — AERONAUTICAL STANDARDS GROUP DEPT OF NAVY AND AIR FORCE (USA)
SPECIFICATIONS
ring_styleCONCENTRIC
joint_styleDIAGONAL JOINT
inside_diameter0.938 INCHES NOMINAL IN
outside_diameter1.157 INCHES NOMINAL IN
material_thickness0.125 INCHES NOMINAL IN
fsc_application_dataHYDRAULIC SYSTEM,ACFT
outer_edge_thickness0.094 INCHES NOMINAL IN
cross-sectional_shape_styleOUTSIDE GROOVED, STRAIGHT FACE
NSN5330-00-580-6646
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: AN6231-8 MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
INSIDE DIAMETER: 0.938 INCHES NOMINAL IN
•
OUTSIDE DIAMETER: 1.157 INCHES NOMINAL IN
•
FSC APPLICATION DATA: HYDRAULIC SYSTEM,ACFT
•
RING STYLE: CONCENTRIC
•
JOINT STYLE: DIAGONAL JOINT
•
TEST DATA DOCUMENT: 81349-MIL-S-5049 SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.).
•
CROSS-SECTIONAL SHAPE STYLE: OUTSIDE GROOVED, STRAIGHT FACE
•
OUTER EDGE THICKNESS: 0.094 INCHES NOMINAL IN
TECHNICAL CHARACTERISTICS (FLIS)
INSIDE DIAMETER0.938 INCHES NOMINAL IN
OUTSIDE DIAMETER1.157 INCHES NOMINAL IN
FSC APPLICATION DATAHYDRAULIC SYSTEM,ACFT
RING STYLECONCENTRIC
JOINT STYLEDIAGONAL JOINT
TEST DATA DOCUMENT81349-MIL-S-5049 SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.).
CROSS-SECTIONAL SHAPE STYLEOUTSIDE GROOVED, STRAIGHT FACE
OUTER EDGE THICKNESS0.094 INCHES NOMINAL IN
MATERIAL THICKNESS0.125 INCHES NOMINAL IN
VERIFIED SUBSTITUTES & CROSS-REFERENCES 27
G8Interchangeable
interchangeable cross-reference
interchangeable
1ACL13Interchangeable
interchangeable cross-reference
interchangeable
102931Interchangeable
interchangeable cross-reference
interchangeable
6191-24VDCInterchangeable
interchangeable cross-reference
interchangeable
S8-WInterchangeable
interchangeable cross-reference
interchangeable
B8VWInterchangeable
interchangeable cross-reference
interchangeable
LIFECYCLE
StatusACTIVE
AvailabilityOEM and secondary market
RoHS CompliantEAR99Not HAZMAT
Ready to buy AN6231-8?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is AN6231-8?
AN6231-8 is a RING,WIPER.
What parts can replace AN6231-8?
There are 27 known substitutes for AN6231-8: G8, 1ACL13, 102931 and 24 more. Substitute compatibility should be verified for your specific system.
What is the NSN for AN6231-8?
AN6231-8 is cataloged in the Federal Logistics Information System (FLIS) under NSN 5330-00-580-6646. This indicates validated use in U.S. government and defense supply chains.
Community Feedback
Comments (0)
No comments yet. Be the first to share what you know.
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — AN6231-8

✓ Validated with multiple authoritative sources, including Government, OEM, and Certified sources.
PartsTable Design LLC · partstable.com
Last verified: July 2026