PartsTable
Technical Data Sheet
Download PDF

A116 — IMPELLER,PUMP,CENTRIFUGAL

✓ Government record, cited
— · MRO · MRO_GENERAL
PRODUCT OVERVIEW

A116: IMPELLER,PUMP,CENTRIFUGAL.

The IMPELLER,PUMP,CENTRIFUGAL is a the manufacturer industrial component. Key specifications include special_features: FULL LOAD CURRENT OF MOTOR STARTER 0.97 TO 1.04 AMP;UNPACKAGED UNIT WEIGHT:0.500 POUNDS;0.650 CUBIC INS. LBS, end_item_identification: USED IN SQUARE-D MANUAL STARTERS ABOARD VARIOUS COAST GUARD VESSELS.

This part is cataloged in the U.S. Government catalog under NSN 5331-00-069-9128, indicating validated use in U.S. government and defense logistics supply chains.

Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels. Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
MRO→ MRO_GENERAL→ A116
NSN: 5331-00-069-9128
NIINs: 000699128, 003989406, 004121333, 008053340, 010839694, 012377515
FSC: 5331 — O-ring
CAGE: 09990 — PARKER-HANNIFIN CORPORATION DBA PNEUTRONICS DIV HYDRAULIC VALVE DIVISION (USA)
SPECIFICATIONS
special_featuresFULL LOAD CURRENT OF MOTOR STARTER 0.97 TO 1.04 AMP;UNPACKAGED UNIT WEIGHT:0.500 POUNDS;0.650 CUBIC INS. LBS
end_item_identificationUSED IN SQUARE-D MANUAL STARTERS ABOARD VARIOUS COAST GUARD VESSELS
NSN5331-00-069-9128
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: A116 MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
CROSS-SECTIONAL HEIGHT: 0.100 INCHES MINIMUM AND 0.106 INCHES MAXIMUM IN
•
CENTER HOLE DIAMETER: 0.732 INCHES MINIMUM AND 0.742 INCHES MAXIMUM IN
•
MATERIAL: RUBBER SYNTHETIC
TECHNICAL CHARACTERISTICS
CROSS-SECTIONAL HEIGHT0.100 INCHES MINIMUM AND 0.106 INCHES MAXIMUM IN
CENTER HOLE DIAMETER0.732 INCHES MINIMUM AND 0.742 INCHES MAXIMUM IN
MATERIALRUBBER SYNTHETIC
SUBSTITUTES & CROSS-REFERENCES 1
19310P11Reference document
Same NSN cross-reference
Reference document — Secondary reference
LIFECYCLE
NSN statusActive· U.S. Government catalog
Acquisition advice: Normally procured from the manufacturer (OEM)No demilitarization required
Ready to buy A116?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is A116?
A116 is a IMPELLER,PUMP,CENTRIFUGAL. It is classified as a MRO (MRO_GENERAL).
What parts can replace A116?
There is 1 known substitute for A116: 19310P11. Substitute compatibility should be verified for your specific system.
What is the NSN for A116?
A116 is cataloged in the U.S. Government catalog under NSN 5331-00-069-9128. This indicates validated use in U.S. government and defense supply chains.
Community Feedback
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — A116