PartsTable
Technical Data Sheet
Download PDF

78647-1J — CLIP,SPRING TENSION

✓ Government record, cited
— · ORING SEAL
PRODUCT OVERVIEW

78647-1J: CLIP,SPRING TENSION.

The CLIP,SPRING TENSION is a the manufacturer industrial component. Key specifications include width: 0.359 INCHES NOMINAL IN, length: 0.406 INCHES NOMINAL IN, material: STEEL COMP 1095 OVERALL, surface_treatment: ZINC OVERALL, material_thickness: 0.024 INCHES MINIMUM AND 0.026 INCHES MAXIMUM IN, material_document_and_classification: SAE ASSN STD SINGLE MATERIAL RESPONSE OVERALL. This part is cataloged in the U.S.

Government catalog under NSN 5340-01-096-2377, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.

Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
78647-1J
NSN: 5340-01-096-2377
FSC: 5340 — Hardware, Commercial
CAGE: 60703 — TRICO PRODUCTS CORPORATION (USA)
SPECIFICATIONS
width0.359 INCHES NOMINAL IN
length0.406 INCHES NOMINAL IN
materialSTEEL COMP 1095 OVERALL
surface_treatmentZINC OVERALL
material_thickness0.024 INCHES MINIMUM AND 0.026 INCHES MAXIMUM IN
material_document_and_classificationSAE ASSN STD SINGLE MATERIAL RESPONSE OVERALL
NSN5340-01-096-2377
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: 78647-1J MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
LENGTH: 0.406 INCHES NOMINAL IN
•
MATERIAL DOCUMENT AND CLASSIFICATION: SAE ASSN STD SINGLE MATERIAL RESPONSE OVERALL
•
MATERIAL THICKNESS: 0.024 INCHES MINIMUM AND 0.026 INCHES MAXIMUM IN
•
SURFACE TREATMENT: ZINC OVERALL
•
WIDTH: 0.359 INCHES NOMINAL IN
•
MATERIAL: STEEL COMP 1095 OVERALL
TECHNICAL CHARACTERISTICS
LENGTH0.406 INCHES NOMINAL IN
MATERIAL DOCUMENT AND CLASSIFICATIONSAE ASSN STD SINGLE MATERIAL RESPONSE OVERALL
MATERIAL THICKNESS0.024 INCHES MINIMUM AND 0.026 INCHES MAXIMUM IN
SURFACE TREATMENTZINC OVERALL
WIDTH0.359 INCHES NOMINAL IN
MATERIALSTEEL COMP 1095 OVERALL
SUBSTITUTES & CROSS-REFERENCES 2
78647Reference document
Same NSN cross-reference
Reference document — Secondary reference
5585118Same NSN cross-reference
Same NSN cross-reference
Also cataloged under this NSN
LIFECYCLE
NSN statusActive· U.S. Government catalog
Acquisition advice: Normally procured from the manufacturer (OEM)No demilitarization required
Ready to buy 78647-1J?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is 78647-1J?
78647-1J is a CLIP,SPRING TENSION.
What parts can replace 78647-1J?
There are 2 known substitutes for 78647-1J: 78647, 5585118. Substitute compatibility should be verified for your specific system.
What is the NSN for 78647-1J?
78647-1J is cataloged in the U.S. Government catalog under NSN 5340-01-096-2377. This indicates validated use in U.S. government and defense supply chains.
Community Feedback
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — 78647-1J