PartsTable
Technical Data Sheet
Download PDF

5585118 — CLIP,SPRING TENSION

✓ Government record, cited
— · ORING SEAL
PRODUCT OVERVIEW

5585118: CLIP,SPRING TENSION.

The CLIP,SPRING TENSION is a the manufacturer industrial component. Key specifications include width: 0.359 INCHES NOMINAL IN, length: 0.406 INCHES NOMINAL IN, material: STEEL COMP 1095 OVERALL, surface_treatment: ZINC OVERALL, material_thickness: 0.024 INCHES MINIMUM AND 0.026 INCHES MAXIMUM IN, material_document_and_classification: SAE ASSN STD SINGLE MATERIAL RESPONSE OVERALL. This part is cataloged in the U.S.

Government catalog under NSN 5340-01-096-2377, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.

Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
5585118
NSN: 5340-01-096-2377
FSC: 5340 — Hardware, Commercial
CAGE: 34623 — AM GENERAL LLC (USA)
SPECIFICATIONS
width0.359 INCHES NOMINAL IN
length0.406 INCHES NOMINAL IN
materialSTEEL COMP 1095 OVERALL
surface_treatmentZINC OVERALL
material_thickness0.024 INCHES MINIMUM AND 0.026 INCHES MAXIMUM IN
material_document_and_classificationSAE ASSN STD SINGLE MATERIAL RESPONSE OVERALL
NSN5340-01-096-2377
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: 5585118 MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
LENGTH: 0.406 INCHES NOMINAL IN
•
MATERIAL DOCUMENT AND CLASSIFICATION: SAE ASSN STD SINGLE MATERIAL RESPONSE OVERALL
•
MATERIAL THICKNESS: 0.024 INCHES MINIMUM AND 0.026 INCHES MAXIMUM IN
•
SURFACE TREATMENT: ZINC OVERALL
•
WIDTH: 0.359 INCHES NOMINAL IN
•
MATERIAL: STEEL COMP 1095 OVERALL
TECHNICAL CHARACTERISTICS
LENGTH0.406 INCHES NOMINAL IN
MATERIAL DOCUMENT AND CLASSIFICATIONSAE ASSN STD SINGLE MATERIAL RESPONSE OVERALL
MATERIAL THICKNESS0.024 INCHES MINIMUM AND 0.026 INCHES MAXIMUM IN
SURFACE TREATMENTZINC OVERALL
WIDTH0.359 INCHES NOMINAL IN
MATERIALSTEEL COMP 1095 OVERALL
SUBSTITUTES & CROSS-REFERENCES 1
78647Reference document
Same NSN cross-reference
Reference document — Secondary reference
LIFECYCLE
NSN statusActive· U.S. Government catalog
Acquisition advice: Normally procured from the manufacturer (OEM)No demilitarization required
Ready to buy 5585118?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is 5585118?
5585118 is a CLIP,SPRING TENSION.
What parts can replace 5585118?
There is 1 known substitute for 5585118: 78647. Substitute compatibility should be verified for your specific system.
What is the NSN for 5585118?
5585118 is cataloged in the U.S. Government catalog under NSN 5340-01-096-2377. This indicates validated use in U.S. government and defense supply chains.
Community Feedback
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — 5585118