PartsTable
Technical Data Sheet
Download PDF

6023-2A — CLIP,SPRING TENSION

✓ Government record, cited
— · ORING SEAL
PRODUCT OVERVIEW

6023-2A: CLIP,SPRING TENSION.

The CLIP,SPRING TENSION is a the manufacturer industrial component. Key specifications include width: 1.990 INCHES MINIMUM AND 2.010 INCHES MAXIMUM IN, length: 1.290 INCHES MINIMUM AND 1.330 INCHES MAXIMUM IN, material: STEEL OVERALL, hole_diameter: 0.159 INCHES MINIMUM AND 0.165 INCHES MAXIMUM IN, overall_height: 1.330 INCHES MINIMUM AND 1.370 INCHES MAXIMUM IN, mounting_method: UNTHREADED HOLE(S). This part is cataloged in the U.S.

Government catalog under NSN 5340-01-019-2981, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.

Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
6023-2A
NSN: 5340-01-019-2981
FSC: 5340 — Hardware, Commercial
CAGE: 91506 — AUGAT INC (USA)
SPECIFICATIONS
width1.990 INCHES MINIMUM AND 2.010 INCHES MAXIMUM IN
length1.290 INCHES MINIMUM AND 1.330 INCHES MAXIMUM IN
materialSTEEL OVERALL
hole_diameter0.159 INCHES MINIMUM AND 0.165 INCHES MAXIMUM IN
overall_height1.330 INCHES MINIMUM AND 1.370 INCHES MAXIMUM IN
mounting_methodUNTHREADED HOLE(S)
surface_treatmentCADMIUM AND CHROMATE OVERALL
material_thickness0.029 INCHES MINIMUM AND 0.035 INCHES MAXIMUM IN
special_test_featuresSPECIAL QUALITY CONTROL TESTING
loop/holding_dimension1.240 INCHES MINIMUM AND 1.260 INCHES MAXIMUM IN
departure_from_cited_documentAS DIFFERENTIATED BY MATERIAL WHICH MUST CONFORM TO SHIPS PARTS CONTROL CENTER SPECIAL QUALITY CONTROL PROVISIONS
distance_from_loop_center_to_end0.720 INCHES MINIMUM AND 0.730 INCHES MAXIMUM IN
NSN5340-01-019-2981
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: 6023-2A MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
LENGTH: 1.290 INCHES MINIMUM AND 1.330 INCHES MAXIMUM IN
•
SURFACE TREATMENT DOCUMENT AND CLASSIFICATION: QQ-P-416,TYPE 2,CLASS 2 FED SPEC SINGLE TREATMENT RESPONSE OVERALL
•
SPECIAL TEST FEATURES: SPECIAL QUALITY CONTROL TESTING
•
MOUNTING METHOD: UNTHREADED HOLE(S)
•
MATERIAL DOCUMENT AND CLASSIFICATION: ASTM A682 ASSN STD ALL MATERIAL RESPONSES OR ASTM A684 ASSN STD ALL MATERIAL RESPONSES OVERALL
•
LOOP/HOLDING DIMENSION: 1.240 INCHES MINIMUM AND 1.260 INCHES MAXIMUM IN
•
MATERIAL THICKNESS: 0.029 INCHES MINIMUM AND 0.035 INCHES MAXIMUM IN
TECHNICAL CHARACTERISTICS
OVERALL HEIGHT1.330 INCHES MINIMUM AND 1.370 INCHES MAXIMUM IN
LENGTH1.290 INCHES MINIMUM AND 1.330 INCHES MAXIMUM IN
SURFACE TREATMENT DOCUMENT AND CLASSIFICATIONQQ-P-416,TYPE 2,CLASS 2 FED SPEC SINGLE TREATMENT RESPONSE OVERALL
SPECIAL TEST FEATURESSPECIAL QUALITY CONTROL TESTING
MOUNTING METHODUNTHREADED HOLE(S)
MATERIAL DOCUMENT AND CLASSIFICATIONASTM A682 ASSN STD ALL MATERIAL RESPONSES OR ASTM A684 ASSN STD ALL MATERIAL RESPONSES OVERALL
LOOP/HOLDING DIMENSION1.240 INCHES MINIMUM AND 1.260 INCHES MAXIMUM IN
MATERIAL THICKNESS0.029 INCHES MINIMUM AND 0.035 INCHES MAXIMUM IN
DEPARTURE FROM CITED DOCUMENTAS DIFFERENTIATED BY MATERIAL WHICH MUST CONFORM TO SHIPS PARTS CONTROL CENTER SPECIAL QUALITY CONTROL PROVISIONS
DISTANCE FROM LOOP CENTER TO END0.720 INCHES MINIMUM AND 0.730 INCHES MAXIMUM IN
SUBSTITUTES & CROSS-REFERENCES 4
16412246Same NSN cross-reference
Same NSN cross-reference
Also cataloged under this NSN
NASM24066/2Reference document
Same NSN cross-reference
Reference document — Design control — primary reference
MIL-C-24066/2Reference document
Same NSN cross-reference
Reference document — Secondary reference
M24066/2-146Reference document
Same NSN cross-reference
Reference document — Secondary reference
LIFECYCLE
NSN statusActive· U.S. Government catalog
Acquisition advice: Normally procured from the manufacturer (OEM)No demilitarization required
Ready to buy 6023-2A?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is 6023-2A?
6023-2A is a CLIP,SPRING TENSION.
What parts can replace 6023-2A?
There are 4 known substitutes for 6023-2A: 16412246, NASM24066/2, MIL-C-24066/2 and 1 more. Substitute compatibility should be verified for your specific system.
What is the NSN for 6023-2A?
6023-2A is cataloged in the U.S. Government catalog under NSN 5340-01-019-2981. This indicates validated use in U.S. government and defense supply chains.
Community Feedback
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — 6023-2A

✓ PartsTable — the parts reference. Every fact cited to its source.
PartsTable Design LLC · partstable.com
U.S. Government catalog: edition PUBLOGDVD v12.0.0 (OCT 2026), edition date 2026-10-01, retrieved 2026-10-18.
PartsTable commercial catalog: edition Unified commercial catalog snapshot through 2026-09-28, edition date not on file, retrieved 2026-09-28.