PartsTable
Technical Data Sheet
58A5A77-27 ✓ Verified by PartsTable
· ORING SEAL
WHAT YOU NEED TO KNOW
Material determines chemical compatibility Standard durometer is 70 Shore A
Wrong material = catastrophic seal failure
PRODUCT OVERVIEW

The CLIP,SPRING TENSION is a the manufacturer industrial component. Key specifications include width: 0.750 INCHES NOMINAL IN, length: 0.344 INCHES NOMINAL IN, material: STEEL COMP 1065 OVERALL, hole_diameter: 0.089 INCHES NOMINAL IN, overall_height: 0.380 INCHES NOMINAL IN, surface_treatment: CADMIUM OVERALL. This part is cataloged in the Federal Logistics Information System (FLIS) under NSN 5340-00-894-2043, indicating validated use in U.S.

government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels. Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
58A5A77-27
NSN: 5340-00-894-2043
FSC: 5340
CAGE: 02387 — NAVAL AIR WARFARE CENTER AIRCRAFT DIV (USA)
SPECIFICATIONS
width0.750 INCHES NOMINAL IN
length0.344 INCHES NOMINAL IN
materialSTEEL COMP 1065 OVERALL
hole_diameter0.089 INCHES NOMINAL IN
overall_height0.380 INCHES NOMINAL IN
surface_treatmentCADMIUM OVERALL
material_thickness0.016 INCHES NOMINAL IN
loop/holding_dimension0.312 INCHES NOMINAL IN
distance_from_loop_center_to_end0.190 INCHES NOMINAL IN
material_document_and_classificationSAE ASSN STD SINGLE MATERIAL RESPONSE OVERALL
NSN5340-00-894-2043
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: 58A5A77-27 MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
LOOP/HOLDING DIMENSION: 0.312 INCHES NOMINAL IN
HOLE DIAMETER: 0.089 INCHES NOMINAL IN
DISTANCE FROM LOOP CENTER TO END: 0.190 INCHES NOMINAL IN
SURFACE TREATMENT: CADMIUM OVERALL
MATERIAL THICKNESS: 0.016 INCHES NOMINAL IN
LENGTH: 0.344 INCHES NOMINAL IN
MATERIAL DOCUMENT AND CLASSIFICATION: SAE ASSN STD SINGLE MATERIAL RESPONSE OVERALL
TECHNICAL CHARACTERISTICS (FLIS)
LOOP/HOLDING DIMENSION0.312 INCHES NOMINAL IN
HOLE DIAMETER0.089 INCHES NOMINAL IN
DISTANCE FROM LOOP CENTER TO END0.190 INCHES NOMINAL IN
SURFACE TREATMENTCADMIUM OVERALL
MATERIAL THICKNESS0.016 INCHES NOMINAL IN
LENGTH0.344 INCHES NOMINAL IN
MATERIAL DOCUMENT AND CLASSIFICATIONSAE ASSN STD SINGLE MATERIAL RESPONSE OVERALL
OVERALL HEIGHT0.380 INCHES NOMINAL IN
WIDTH0.750 INCHES NOMINAL IN
MATERIALSTEEL COMP 1065 OVERALL
VERIFIED SUBSTITUTES & CROSS-REFERENCES 4
416949-7Interchangeable
interchangeable cross-reference
interchangeable
139-2230-000Interchangeable
interchangeable cross-reference
interchangeable
100-200-5-10Interchangeable
interchangeable cross-reference
interchangeable
908C913-8Interchangeable
Same NIIN cross-reference
interchangeable
LIFECYCLE
StatusCANCELLED
Availability
RoHS CompliantEAR99Not HAZMAT
Ready to buy 58A5A77-27?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is 58A5A77-27?
58A5A77-27 is a CLIP,SPRING TENSION.
What parts can replace 58A5A77-27?
There are 4 known substitutes for 58A5A77-27: 416949-7, 139-2230-000, 100-200-5-10 and 1 more. Substitute compatibility should be verified for your specific system.
Is 58A5A77-27 still available?
58A5A77-27 is currently cancelled.
Community Feedback
Comments (0)
No comments yet. Be the first to share what you know.
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — 58A5A77-27