PartsTable
Technical Data Sheet
Download PDF

500192-1 — WASHER,FLAT

✓ Government record, cited
— · ORING SEAL
PRODUCT OVERVIEW

500192-1: WASHER,FLAT.

The WASHER,FLAT is a the manufacturer industrial component. Key specifications include width: 0.500 INCHES NOMINAL IN, height: 0.120 INCHES NOMINAL IN, material: STEEL COMP 303, hole_diameter: 0.187 INCHES MINIMUM AND 0.188 INCHES MAXIMUM IN, furnished_items: LOCKNUT, surface_treatment: PASSIVATE. This part is cataloged in the U.S.

Government catalog under NSN 5340-00-911-8913, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.

Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
500192-1
NSN: 5340-00-911-8913
NIINs: 009118913, 013407235
FSC: 5340 — Hardware, Commercial
CAGE: 12909 — CARDION INC (USA)
SPECIFICATIONS
width0.500 INCHES NOMINAL IN
height0.120 INCHES NOMINAL IN
materialSTEEL COMP 303
hole_diameter0.187 INCHES MINIMUM AND 0.188 INCHES MAXIMUM IN
furnished_itemsLOCKNUT
surface_treatmentPASSIVATE
material_document_and_classificationAISI ASSN STD SINGLE MATERIAL RESPONSE
NSN5340-00-911-8913
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: 500192-1 MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
MATERIAL DOCUMENT AND CLASSIFICATION: AISI ASSN STD SINGLE MATERIAL RESPONSE
•
HEIGHT: 0.120 INCHES NOMINAL IN
•
SURFACE TREATMENT: PASSIVATE
•
WIDTH: 0.500 INCHES NOMINAL IN
•
MATERIAL: STEEL COMP 303
•
FURNISHED ITEMS: LOCKNUT
•
HOLE DIAMETER: 0.187 INCHES MINIMUM AND 0.188 INCHES MAXIMUM IN
TECHNICAL CHARACTERISTICS
MATERIAL DOCUMENT AND CLASSIFICATIONAISI ASSN STD SINGLE MATERIAL RESPONSE
HEIGHT0.120 INCHES NOMINAL IN
SURFACE TREATMENTPASSIVATE
WIDTH0.500 INCHES NOMINAL IN
MATERIALSTEEL COMP 303
FURNISHED ITEMSLOCKNUT
HOLE DIAMETER0.187 INCHES MINIMUM AND 0.188 INCHES MAXIMUM IN
SUBSTITUTES & CROSS-REFERENCES 1
03-11Reference document
Same NSN cross-reference
Reference document — Design control — primary reference
LIFECYCLE
NSN statusActive· U.S. Government catalog
Acquisition advice: Normally procured from the manufacturer (OEM)No demilitarization required
Ready to buy 500192-1?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is 500192-1?
500192-1 is a WASHER,FLAT.
What parts can replace 500192-1?
There is 1 known substitute for 500192-1: 03-11. Substitute compatibility should be verified for your specific system.
What is the NSN for 500192-1?
500192-1 is cataloged in the U.S. Government catalog under NSN 5340-00-911-8913. This indicates validated use in U.S. government and defense supply chains.
Community Feedback
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — 500192-1