PartsTable
Technical Data Sheet
PartsTable / MRO / 115-10-4
115-10-4 ✓ Verified by PartsTable
— · MRO · MRO_GENERAL
WHAT YOU NEED TO KNOW
Material determines chemical compatibility Standard durometer is 70 Shore A
Wrong material = catastrophic seal failure
PRODUCT OVERVIEW

The RESISTOR,FIXED,WIRE WOUND is a the manufacturer industrial component. Key specifications include diameter: 0.204 INCHES NOMINAL IN, material: RUBBER SYNTHETIC CUSHION, overall_width: 0.500 INCHES NOMINAL IN, style_designator: OFFSET MOUNT, tongue_hole_type: ROUND, UNTHREADED, material_thickness: 0.032 INCHES NOMINAL IN. This part is cataloged in the Federal Logistics Information System (FLIS) under NSN 5340-00-565-0011, indicating validated use in U.S.

government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels. Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
MRO→ MRO_GENERAL→ 115-10-4
NSN: 5340-00-565-0011
FSC: 5340
CAGE: 88818 — KEARFOTT CORPORATION DIV GUIDANCE AND NAVIGATION DIVISION (USA)
SPECIFICATIONS
diameter0.204 INCHES NOMINAL IN
materialRUBBER SYNTHETIC CUSHION
overall_width0.500 INCHES NOMINAL IN
style_designatorOFFSET MOUNT
tongue_hole_typeROUND, UNTHREADED
material_thickness0.032 INCHES NOMINAL IN
loop_inside_diameter0.125 INCHES NOMINAL IN
specification/standard_data88818-115-10-4 MANUFACTURERS STANDARD
material_document_and_classificationQQ-A-362,T4 FED SPEC SINGLE MATERIAL RESPONSE BAND
distance_from_loop_center_to_tongue_end0.645 INCHES NOMINAL IN
center_to_center_distance_between_loop_and_mounting_hole0.457 INCHES NOMINAL IN
NSN5340-00-565-0011
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: 115-10-4 MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
MATERIAL THICKNESS: 0.032 INCHES NOMINAL IN
•
MATERIAL: RUBBER SYNTHETIC CUSHION
•
DISTANCE FROM LOOP CENTER TO TONGUE END: 0.645 INCHES NOMINAL IN
•
STYLE DESIGNATOR: OFFSET MOUNT
•
CENTER TO CENTER DISTANCE BETWEEN LOOP AND MOUNTING HOLE: 0.457 INCHES NOMINAL IN
•
DIAMETER: 0.204 INCHES NOMINAL IN
•
TONGUE HOLE TYPE: ROUND, UNTHREADED
TECHNICAL CHARACTERISTICS (FLIS)
MATERIAL THICKNESS0.032 INCHES NOMINAL IN
MATERIALRUBBER SYNTHETIC CUSHION
DISTANCE FROM LOOP CENTER TO TONGUE END0.645 INCHES NOMINAL IN
OVERALL WIDTH0.500 INCHES NOMINAL IN
STYLE DESIGNATOROFFSET MOUNT
CENTER TO CENTER DISTANCE BETWEEN LOOP AND MOUNTING HOLE0.457 INCHES NOMINAL IN
DIAMETER0.204 INCHES NOMINAL IN
TONGUE HOLE TYPEROUND, UNTHREADED
MATERIALALUMINUM ALLOY 2024 BAND
SPECIFICATION/STANDARD DATA88818-115-10-4 MANUFACTURERS STANDARD
VERIFIED SUBSTITUTES & CROSS-REFERENCES 26
16028P11Upgraded Successor
successor cross-reference
successor
4CUpgraded Successor
successor cross-reference
successor
2781-4Interchangeable
interchangeable cross-reference
interchangeable
RH19B25Interchangeable
interchangeable cross-reference
interchangeable
Y15084Interchangeable
interchangeable cross-reference
interchangeable
406Interchangeable
interchangeable cross-reference
interchangeable
LIFECYCLE
StatusCANCELLED
Availability—
RoHS CompliantEAR99Not HAZMAT
Ready to buy 115-10-4?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is 115-10-4?
115-10-4 is a RESISTOR,FIXED,WIRE WOUND. It is classified as a MRO (MRO_GENERAL).
What parts can replace 115-10-4?
There are 26 known substitutes for 115-10-4: 16028P11, 4C, 2781-4 and 23 more. Substitute compatibility should be verified for your specific system.
Is 115-10-4 still available?
115-10-4 is currently cancelled.
Community Feedback
Comments (0)
No comments yet. Be the first to share what you know.
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — 115-10-4

✓ Validated with multiple authoritative sources, including Government, OEM, and Certified sources.
PartsTable Design LLC · partstable.com
Last verified: July 2026