PartsTable
Technical Data Sheet
PartsTable / COMPONENT / 113857
113857 ✓ Verified by PartsTable
— · ORING SEAL
WHAT YOU NEED TO KNOW
Material determines chemical compatibility Standard durometer is 70 Shore A
Wrong material = catastrophic seal failure
PRODUCT OVERVIEW

The GASKET is a the manufacturer industrial component. Key specifications include hole_diameter: 0.281 INCHES NOMINAL LOCATION NOT OTHERWISE SPECIFIED IN, overall_width: 2.840 INCHES MINIMUM IN, overall_length: 2.840 INCHES MINIMUM IN, aperture_diameter: 1.360 INCHES MAXIMUM IN, surface_treatment: ANODIZE OVERALL, gage_ring_thickness: 0.091 INCHES NOMINAL IN. This part is cataloged in the Federal Logistics Information System (FLIS) under NSN 5330-00-825-8451, indicating validated use in U.S.

government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels. Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
113857
NSN: 5330-00-825-8451
FSC: 5330
CAGE: 83259 — PARKER-HANNIFIN CORPORATION DBA PNEUTRONICS DIV COMPOSITE SEALING SYSTEMS DIVISION (USA)
SPECIFICATIONS
hole_diameter0.281 INCHES NOMINAL LOCATION NOT OTHERWISE SPECIFIED IN
overall_width2.840 INCHES MINIMUM IN
overall_length2.840 INCHES MINIMUM IN
aperture_diameter1.360 INCHES MAXIMUM IN
surface_treatmentANODIZE OVERALL
gage_ring_thickness0.091 INCHES NOMINAL IN
fsc_application_dataACFT STRUCTURAL COMPONENTS,AIRFRAME
outside_corner_radius0.600 INCHES MAXIMUM IN
cross-sectional_thickness0.130 INCHES NOMINAL IN
cross-sectional_shape_styleMETAL AND SYNTHETIC RUBBER
surface_treatment_document_and_classificationMIL-A-8625 MIL SPEC SINGLE TREATMENT RESPONSE OVERALL
outside_edge_to_bolt_hole_center_distance_along_width0.600 INCHES NOMINAL IN
NSN5330-00-825-8451
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: 113857 MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
CENTER TO CENTER DISTANCE BETWEEN BOLT HOLES ALONG WIDTH: 1.640 INCHES NOMINAL LOCATION NOT OTHERWISE SPECIFIED IN
•
HOLE DIAMETER: 0.281 INCHES NOMINAL LOCATION NOT OTHERWISE SPECIFIED IN
•
OUTSIDE EDGE TO BOLT HOLE CENTER DISTANCE ALONG LENGTH: 0.600 INCHES NOMINAL IN
•
SURFACE TREATMENT: ANODIZE OVERALL
•
CENTER TO CENTER DISTANCE BETWEEN BOLT HOLES ALONG LENGTH: 1.640 INCHES NOMINAL LOCATION NOT OTHERWISE SPECIFIED IN
•
CROSS-SECTIONAL THICKNESS: 0.130 INCHES NOMINAL IN
•
OUTSIDE EDGE TO BOLT HOLE CENTER DISTANCE ALONG WIDTH: 0.600 INCHES NOMINAL IN
TECHNICAL CHARACTERISTICS (FLIS)
CENTER TO CENTER DISTANCE BETWEEN BOLT HOLES ALONG WIDTH1.640 INCHES NOMINAL LOCATION NOT OTHERWISE SPECIFIED IN
HOLE DIAMETER0.281 INCHES NOMINAL LOCATION NOT OTHERWISE SPECIFIED IN
OUTSIDE EDGE TO BOLT HOLE CENTER DISTANCE ALONG LENGTH0.600 INCHES NOMINAL IN
SURFACE TREATMENTANODIZE OVERALL
CENTER TO CENTER DISTANCE BETWEEN BOLT HOLES ALONG LENGTH1.640 INCHES NOMINAL LOCATION NOT OTHERWISE SPECIFIED IN
CROSS-SECTIONAL THICKNESS0.130 INCHES NOMINAL IN
OUTSIDE EDGE TO BOLT HOLE CENTER DISTANCE ALONG WIDTH0.600 INCHES NOMINAL IN
OVERALL WIDTH2.840 INCHES MINIMUM IN
GAGE RING THICKNESS0.091 INCHES NOMINAL IN
APERTURE DIAMETER1.360 INCHES MAXIMUM IN
VERIFIED SUBSTITUTES & CROSS-REFERENCES 12
07-02762-0AInterchangeable
interchangeable cross-reference
interchangeable
2762Interchangeable
interchangeable cross-reference
interchangeable
297669-1007Interchangeable
interchangeable cross-reference
interchangeable
298176-6Interchangeable
interchangeable cross-reference
interchangeable
M7405536-1Interchangeable
interchangeable cross-reference
interchangeable
00737 TY SH 47 ST 164Interchangeable
interchangeable cross-reference
interchangeable
LIFECYCLE
StatusCANCELLED
Availability—
RoHS CompliantEAR99Not HAZMAT
Ready to buy 113857?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is 113857?
113857 is a GASKET.
What parts can replace 113857?
There are 12 known substitutes for 113857: 07-02762-0A, 2762, 297669-1007 and 9 more. Substitute compatibility should be verified for your specific system.
Is 113857 still available?
113857 is currently cancelled.
Community Feedback
Comments (0)
No comments yet. Be the first to share what you know.
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — 113857

✓ Validated with multiple authoritative sources, including Government, OEM, and Certified sources.
PartsTable Design LLC · partstable.com
Last verified: July 2026