PartsTable
Technical Data Sheet
Download PDF

100-200-18-16 — CLIP,SPRING TENSION

✓ Government record, cited
— · ORING SEAL
PRODUCT OVERVIEW

100-200-18-16: CLIP,SPRING TENSION.

The CLIP,SPRING TENSION is a the manufacturer industrial component. Key specifications include width: 1.990 INCHES MINIMUM AND 2.010 INCHES MAXIMUM IN, length: 1.290 INCHES MINIMUM AND 1.330 INCHES MAXIMUM IN, material: STEEL OVERALL, hole_diameter: 0.159 INCHES MINIMUM AND 0.165 INCHES MAXIMUM IN, overall_height: 1.330 INCHES MINIMUM AND 1.370 INCHES MAXIMUM IN, mounting_method: UNTHREADED HOLE(S). This part is cataloged in the U.S.

Government catalog under NSN 5340-01-009-6848, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.

Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
100-200-18-16
NSN: 5340-01-009-6848
FSC: 5340 — Hardware, Commercial
CAGE: 99378 — ATLEE OF DELAWARE, INCORPORATED (USA)
SPECIFICATIONS
width1.990 INCHES MINIMUM AND 2.010 INCHES MAXIMUM IN
length1.290 INCHES MINIMUM AND 1.330 INCHES MAXIMUM IN
materialSTEEL OVERALL
hole_diameter0.159 INCHES MINIMUM AND 0.165 INCHES MAXIMUM IN
overall_height1.330 INCHES MINIMUM AND 1.370 INCHES MAXIMUM IN
mounting_methodUNTHREADED HOLE(S)
material_thickness0.029 INCHES MINIMUM AND 0.035 INCHES MAXIMUM IN
loop/holding_dimension1.240 INCHES MINIMUM AND 1.260 INCHES MAXIMUM IN
distance_from_loop_center_to_end0.720 INCHES MINIMUM IN
material_document_and_classificationASTM A682 ASSN STD SINGLE MATERIAL RESPONSE OVERALL
NSN5340-01-009-6848
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: 100-200-18-16 MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
LENGTH: 1.290 INCHES MINIMUM AND 1.330 INCHES MAXIMUM IN
•
MOUNTING METHOD: UNTHREADED HOLE(S)
•
MATERIAL DOCUMENT AND CLASSIFICATION: ASTM A682 ASSN STD SINGLE MATERIAL RESPONSE OVERALL
•
LOOP/HOLDING DIMENSION: 1.240 INCHES MINIMUM AND 1.260 INCHES MAXIMUM IN
•
MATERIAL THICKNESS: 0.029 INCHES MINIMUM AND 0.035 INCHES MAXIMUM IN
•
DISTANCE FROM LOOP CENTER TO END: 0.720 INCHES MINIMUM IN
•
WIDTH: 1.990 INCHES MINIMUM AND 2.010 INCHES MAXIMUM IN
TECHNICAL CHARACTERISTICS
OVERALL HEIGHT1.330 INCHES MINIMUM AND 1.370 INCHES MAXIMUM IN
LENGTH1.290 INCHES MINIMUM AND 1.330 INCHES MAXIMUM IN
MOUNTING METHODUNTHREADED HOLE(S)
MATERIAL DOCUMENT AND CLASSIFICATIONASTM A682 ASSN STD SINGLE MATERIAL RESPONSE OVERALL
LOOP/HOLDING DIMENSION1.240 INCHES MINIMUM AND 1.260 INCHES MAXIMUM IN
MATERIAL THICKNESS0.029 INCHES MINIMUM AND 0.035 INCHES MAXIMUM IN
DISTANCE FROM LOOP CENTER TO END0.720 INCHES MINIMUM IN
WIDTH1.990 INCHES MINIMUM AND 2.010 INCHES MAXIMUM IN
MATERIALSTEEL OVERALL
HOLE DIAMETER0.159 INCHES MINIMUM AND 0.165 INCHES MAXIMUM IN
SUBSTITUTES & CROSS-REFERENCES 4
NASM24066/2Reference document
Same NSN cross-reference
Reference document — Design control — primary reference
M24066/2-346Reference document
Same NSN cross-reference
Reference document — Secondary reference
MIL-C-24066Reference document
Same NSN cross-reference
Reference document — Secondary reference
M24066-2-146Reference document
Same NSN cross-reference
Reference document — Advisory reference — outside the item-of-supply concept
LIFECYCLE
NSN statusActive· U.S. Government catalog
Acquisition advice: Insurance item — stocked against contingency demandNo demilitarization required
Ready to buy 100-200-18-16?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is 100-200-18-16?
100-200-18-16 is a CLIP,SPRING TENSION.
What parts can replace 100-200-18-16?
There are 4 known substitutes for 100-200-18-16: NASM24066/2, M24066/2-346, MIL-C-24066 and 1 more. Substitute compatibility should be verified for your specific system.
What is the NSN for 100-200-18-16?
100-200-18-16 is cataloged in the U.S. Government catalog under NSN 5340-01-009-6848. This indicates validated use in U.S. government and defense supply chains.
Community Feedback
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — 100-200-18-16

✓ PartsTable — the parts reference. Every fact cited to its source.
PartsTable Design LLC · partstable.com
U.S. Government catalog: edition PUBLOGDVD v12.0.0 (OCT 2026), edition date 2026-10-01, retrieved 2026-10-18.
PartsTable commercial catalog: edition Unified commercial catalog snapshot through 2026-09-28, edition date not on file, retrieved 2026-09-28.