PartsTable
Technical Data Sheet
PartsTable / COMPONENT / TA9C29S8DG
TA9C29S8DG ✓ Verified by PartsTable
— · ORING SEAL
WHAT YOU NEED TO KNOW
Material determines chemical compatibility Standard durometer is 70 Shore A
Wrong material = catastrophic seal failure
PRODUCT OVERVIEW

The CLAMP,LOOP is a the manufacturer industrial component. Key specifications include diameter: 0.204 INCHES NOMINAL IN, material: RUBBER SYNTHETIC CUSHION, overall_width: 0.500 INCHES NOMINAL IN, style_designator: OFFSET MOUNT, tongue_hole_type: ROUND, UNTHREADED, surface_treatment: ANODIZE BAND. This product is currently in active production with full OEM support.

This part is cataloged in the Federal Logistics Information System (FLIS) under NSN 5340-01-213-5533, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.

Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
TA9C29S8DG
NSN: 5340-01-213-5533
FSC: 5340
CAGE: 84971 — TA AEROSPACE CO DIV TA AEROSPACE (USA)
SPECIFICATIONS
diameter0.204 INCHES NOMINAL IN
materialRUBBER SYNTHETIC CUSHION
overall_width0.500 INCHES NOMINAL IN
style_designatorOFFSET MOUNT
tongue_hole_typeROUND, UNTHREADED
surface_treatmentANODIZE BAND
material_thickness0.058 INCHES MINIMUM AND 0.068 INCHES MAXIMUM IN
loop_inside_diameter0.500 INCHES NOMINAL IN
material_document_and_classificationQQ-A-362 FED SPEC SINGLE MATERIAL RESPONSE BAND
distance_from_loop_center_to_tongue_end0.872 INCHES NOMINAL IN
surface_treatment_document_and_classificationMIL-A-8625 MIL SPEC SINGLE TREATMENT RESPONSE BAND
center_to_center_distance_between_loop_and_mounting_hole0.654 INCHES NOMINAL IN
NSN5340-01-213-5533
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: TA9C29S8DG MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
SURFACE TREATMENT DOCUMENT AND CLASSIFICATION: MIL-A-8625 MIL SPEC SINGLE TREATMENT RESPONSE BAND
•
MATERIAL DOCUMENT AND CLASSIFICATION: QQ-A-362 FED SPEC SINGLE MATERIAL RESPONSE BAND
•
CENTER TO CENTER DISTANCE BETWEEN LOOP AND MOUNTING HOLE: 0.654 INCHES NOMINAL IN
•
MATERIAL: RUBBER SYNTHETIC CUSHION
•
TONGUE HOLE TYPE: ROUND, UNTHREADED
•
DIAMETER: 0.204 INCHES NOMINAL IN
•
DISTANCE FROM LOOP CENTER TO TONGUE END: 0.872 INCHES NOMINAL IN
TECHNICAL CHARACTERISTICS (FLIS)
SURFACE TREATMENT DOCUMENT AND CLASSIFICATIONMIL-A-8625 MIL SPEC SINGLE TREATMENT RESPONSE BAND
MATERIAL DOCUMENT AND CLASSIFICATIONQQ-A-362 FED SPEC SINGLE MATERIAL RESPONSE BAND
CENTER TO CENTER DISTANCE BETWEEN LOOP AND MOUNTING HOLE0.654 INCHES NOMINAL IN
OVERALL WIDTH0.500 INCHES NOMINAL IN
MATERIALRUBBER SYNTHETIC CUSHION
TONGUE HOLE TYPEROUND, UNTHREADED
DIAMETER0.204 INCHES NOMINAL IN
DISTANCE FROM LOOP CENTER TO TONGUE END0.872 INCHES NOMINAL IN
STYLE DESIGNATOROFFSET MOUNT
MATERIALALUMINUM ALLOY 2024 BAND
VERIFIED SUBSTITUTES & CROSS-REFERENCES 20
MIL-DTL-8603Upgraded Successor
successor cross-reference
successor
TA1716WS4Upgraded Successor
successor cross-reference
successor
MS21919WG4Upgraded Successor
successor cross-reference
successor
4058Upgraded Successor
successor cross-reference
successor
IV CATHETER PLACEMENT UNITUpgraded Successor
successor cross-reference
successor
10335339Upgraded Successor
successor cross-reference
successor
LIFECYCLE
StatusACTIVE
AvailabilityOEM and secondary market
RoHS CompliantEAR99Not HAZMAT
Ready to buy TA9C29S8DG?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is TA9C29S8DG?
TA9C29S8DG is a CLAMP,LOOP.
What parts can replace TA9C29S8DG?
There are 20 known substitutes for TA9C29S8DG: MIL-DTL-8603, TA1716WS4, MS21919WG4 and 17 more. Substitute compatibility should be verified for your specific system.
What is the NSN for TA9C29S8DG?
TA9C29S8DG is cataloged in the Federal Logistics Information System (FLIS) under NSN 5340-01-213-5533. This indicates validated use in U.S. government and defense supply chains.
Community Feedback
Comments (0)
No comments yet. Be the first to share what you know.
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — TA9C29S8DG

✓ Validated with multiple authoritative sources, including Government, OEM, and Certified sources.
PartsTable Design LLC · partstable.com
Last verified: July 2026