TA713SS7HR — CLAMP,LOOP

✓ Government record, cited

— · ORING SEAL

PRODUCT OVERVIEW

TA713SS7HR: CLAMP,LOOP.

The CLAMP,LOOP is a the manufacturer industrial component. Key specifications include diameter: 0.199 INCHES NOMINAL IN, material: STEEL COMP 302 OR STEEL COMP 321 BAND, overall_width: 0.375 INCHES NOMINAL IN, special_features: TONGUE END RADIUS 0.375 IN. NOM; CUSION 0.500 IN.

NOM W IN, style_designator: OFFSET MOUNT, tongue_hole_type: ROUND, UNTHREADED. This part is cataloged in the U.S. Government catalog under NSN 5340-01-216-2973, indicating validated use in U.S.

government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels. Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS

TA713SS7HR

NSN: 5340-01-216-2973
FSC: 5340 — Hardware, Commercial
CAGE: 84971 — TA AEROSPACE CO DIV TA AEROSPACE (USA)

SPECIFICATIONS

diameter	0.199 INCHES NOMINAL IN
material	STEEL COMP 302 OR STEEL COMP 321 BAND
overall_width	0.375 INCHES NOMINAL IN
special_features	TONGUE END RADIUS 0.375 IN. NOM; CUSION 0.500 IN. NOM W IN
style_designator	OFFSET MOUNT
tongue_hole_type	ROUND, UNTHREADED
surface_treatment	PASSIVATE BAND
material_thickness	0.032 INCHES NOMINAL IN
loop_inside_diameter	0.438 INCHES NOMINAL IN
material_document_and_classification	MIL-S-5059 MIL SPEC 1ST MATERIAL RESPONSE OR AMS 5510 ASSN STD 2ND MATERIAL RESPONSE BAND
distance_from_loop_center_to_tongue_end	0.718 INCHES MINIMUM AND 0.738 INCHES MAXIMUM IN
center_to_center_distance_between_loop_and_mounting_hole	0.530 INCHES MINIMUM AND 0.550 INCHES MAXIMUM IN
NSN	5340-01-216-2973

COMPONENT DIAGRAM

KEY FEATURES

•

STYLE DESIGNATOR: OFFSET MOUNT

•

MATERIAL DOCUMENT AND CLASSIFICATION: MIL-S-5059 MIL SPEC 1ST MATERIAL RESPONSE OR AMS 5510 ASSN STD 2ND MATERIAL RESPONSE BAND

•

DIAMETER: 0.199 INCHES NOMINAL IN

•

MATERIAL THICKNESS: 0.032 INCHES NOMINAL IN

•

DISTANCE FROM LOOP CENTER TO TONGUE END: 0.718 INCHES MINIMUM AND 0.738 INCHES MAXIMUM IN

TECHNICAL CHARACTERISTICS

STYLE DESIGNATOR	OFFSET MOUNT
MATERIAL DOCUMENT AND CLASSIFICATION	MIL-S-5059 MIL SPEC 1ST MATERIAL RESPONSE OR AMS 5510 ASSN STD 2ND MATERIAL RESPONSE BAND
MATERIAL DOCUMENT AND CLASSIFICATION	AMS 3300 ASSN STD SINGLE MATERIAL RESPONSE CUSHION
DIAMETER	0.199 INCHES NOMINAL IN
OVERALL WIDTH	0.375 INCHES NOMINAL IN
MATERIAL THICKNESS	0.032 INCHES NOMINAL IN
DISTANCE FROM LOOP CENTER TO TONGUE END	0.718 INCHES MINIMUM AND 0.738 INCHES MAXIMUM IN
SPECIAL FEATURES	TONGUE END RADIUS 0.375 IN. NOM; CUSION 0.500 IN. NOM W IN
SURFACE TREATMENT	PASSIVATE BAND
TONGUE HOLE TYPE	ROUND, UNTHREADED

SUBSTITUTES & CROSS-REFERENCES 4

AS21919CH07Reference document

Same NSN cross-reference

Reference document — Design control — primary reference

MS21919CH7Reference document

Same NSN cross-reference

Reference document — Secondary reference

615-05-25Reference document

Same NSN cross-reference

Reference document — Advisory reference — outside the item-of-supply concept

SAE-AS21919Reference document

Same NSN cross-reference

Reference document — Design control — primary reference

LIFECYCLE

NSN statusActive· U.S. Government catalog

Acquisition advice: Terminal item — stock exhausted; no further procurementNo demilitarization required

Ready to buy TA713SS7HR?

Compare prices from verified sellers on eBay

Buy on eBay →

As an eBay Partner, PartsTable may earn a commission. Your price is not affected.

FREQUENTLY ASKED QUESTIONS

What is TA713SS7HR?

TA713SS7HR is a CLAMP,LOOP.

What parts can replace TA713SS7HR?

There are 4 known substitutes for TA713SS7HR: AS21919CH07, MS21919CH7, 615-05-25 and 1 more. Substitute compatibility should be verified for your specific system.

What is the NSN for TA713SS7HR?

TA713SS7HR is cataloged in the U.S. Government catalog under NSN 5340-01-216-2973. This indicates validated use in U.S. government and defense supply chains.

Community Feedback

TA713SS7HR — CLAMP,LOOP

Request a Quote — TA713SS7HR