PartsTable
Technical Data Sheet
Download PDF

TA0410013 — CLAMP,LOOP

✓ Government record, cited
— · ORING SEAL
PRODUCT OVERVIEW

TA0410013: CLAMP,LOOP.

The CLAMP,LOOP is a the manufacturer industrial component. Key specifications include special_features: PART OF ASSEMBLY OF POTENTIOMETER STEERING USED AS A FIXTURE TO ORIENT CONNECTORS AND POSITION BOOTS DURING ASSEMBLY, end_item_identification: W/S: AIRCRAFT, F-16, center_to_center_distance_between_loop_and_mounting_hole: 0.560 INCHES NOMINAL IN. This part is cataloged in the U.S.

Government catalog under NSN 5340-01-380-8057, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.

Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
TA0410013
NSN: 5340-01-380-8057
FSC: 5340 — Hardware, Commercial
CAGE: 84971 — TA AEROSPACE CO DIV TA AEROSPACE (USA)
SPECIFICATIONS
special_featuresPART OF ASSEMBLY OF POTENTIOMETER STEERING USED AS A FIXTURE TO ORIENT CONNECTORS AND POSITION BOOTS DURING ASSEMBLY
end_item_identificationW/S: AIRCRAFT, F-16
center_to_center_distance_between_loop_and_mounting_hole0.560 INCHES NOMINAL IN
NSN5340-01-380-8057
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: TA0410013 MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
CENTER TO CENTER DISTANCE BETWEEN LOOP AND MOUNTING HOLE: 0.560 INCHES NOMINAL IN
TECHNICAL CHARACTERISTICS
SPECIAL FEATURESPART OF ASSEMBLY OF POTENTIOMETER STEERING USED AS A FIXTURE TO ORIENT CONNECTORS AND POSITION BOOTS DURING ASSEMBLY
END ITEM IDENTIFICATIONW/S: AIRCRAFT, F-16
CENTER TO CENTER DISTANCE BETWEEN LOOP AND MOUNTING HOLE0.560 INCHES NOMINAL IN
SUBSTITUTES & CROSS-REFERENCES 2
C20264-1Reference document
Same NSN cross-reference
Reference document — Vendor item drawing reference
16L080-9Reference document
Same NSN cross-reference
Reference document — Secondary reference
LIFECYCLE
NSN statusActive· U.S. Government catalog
Acquisition advice: Insurance item — stocked against contingency demandNo demilitarization required
Ready to buy TA0410013?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is TA0410013?
TA0410013 is a CLAMP,LOOP.
What parts can replace TA0410013?
There are 2 known substitutes for TA0410013: C20264-1, 16L080-9. Substitute compatibility should be verified for your specific system.
What is the NSN for TA0410013?
TA0410013 is cataloged in the U.S. Government catalog under NSN 5340-01-380-8057. This indicates validated use in U.S. government and defense supply chains.
Community Feedback
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — TA0410013