PartsTable
Technical Data Sheet
Download PDF

PWA50671 — CLAMP,SYNCHRO

✓ Government record, cited
— · ORING SEAL
PRODUCT OVERVIEW

PWA50671: CLAMP,SYNCHRO.

The CLAMP,SYNCHRO is a the manufacturer industrial component. Key specifications include width: 0.375 INCHES NOMINAL IN, height: 0.750 INCHES NOMINAL IN, length: 0.875 INCHES NOMINAL IN, material: STEEL COMP 1018, effective_height: 0.250 INCHES NOMINAL IN, effective_length: 0.500 INCHES NOMINAL IN. This part is cataloged in the U.S.

Government catalog under NSN 5340-00-006-0924, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.

Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
PWA50671
NSN: 5340-00-006-0924
FSC: 5340 — Hardware, Commercial
CAGE: 77445 — RTX CORPORATION DBA PRATT & WHITNEY DIV PRATT &WHITNEY (USA)
SPECIFICATIONS
width0.375 INCHES NOMINAL IN
height0.750 INCHES NOMINAL IN
length0.875 INCHES NOMINAL IN
materialSTEEL COMP 1018
effective_height0.250 INCHES NOMINAL IN
effective_length0.500 INCHES NOMINAL IN
special_featuresORIGINAL NAME, CLAMP REAR COMPRESSOR REAR HUB, HEAT SHIELD; CONSISTS OF 1 STEEL CLAMP, 1 NYLON WASHER, 1 HEX STEEL NUT
style_designatorSQUARE
end_item_identificationPWF100,P100 JET ENG
outside_edge_to_bolt_hole_center_distance_along_length0.688 INCHES NOMINAL IN
NSN5340-00-006-0924
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: PWA50671 MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
LENGTH: 0.875 INCHES NOMINAL IN
•
STYLE DESIGNATOR: SQUARE
•
EFFECTIVE LENGTH: 0.500 INCHES NOMINAL IN
•
EFFECTIVE HEIGHT: 0.250 INCHES NOMINAL IN
•
HEIGHT: 0.750 INCHES NOMINAL IN
•
OUTSIDE EDGE TO BOLT HOLE CENTER DISTANCE ALONG LENGTH: 0.688 INCHES NOMINAL IN
•
WIDTH: 0.375 INCHES NOMINAL IN
TECHNICAL CHARACTERISTICS
LENGTH0.875 INCHES NOMINAL IN
STYLE DESIGNATORSQUARE
EFFECTIVE LENGTH0.500 INCHES NOMINAL IN
EFFECTIVE HEIGHT0.250 INCHES NOMINAL IN
HEIGHT0.750 INCHES NOMINAL IN
SPECIAL FEATURESORIGINAL NAME, CLAMP REAR COMPRESSOR REAR HUB, HEAT SHIELD; CONSISTS OF 1 STEEL CLAMP, 1 NYLON WASHER, 1 HEX STEEL NUT
OUTSIDE EDGE TO BOLT HOLE CENTER DISTANCE ALONG LENGTH0.688 INCHES NOMINAL IN
WIDTH0.375 INCHES NOMINAL IN
END ITEM IDENTIFICATIONPWF100,P100 JET ENG
MATERIALSTEEL COMP 1018
SUBSTITUTES & CROSS-REFERENCES 1
50671Reference document
Same NSN cross-reference
Reference document — Secondary reference
LIFECYCLE
NSN statusActive· U.S. Government catalog
No demilitarization required
Ready to buy PWA50671?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is PWA50671?
PWA50671 is a CLAMP,SYNCHRO.
What parts can replace PWA50671?
There is 1 known substitute for PWA50671: 50671. Substitute compatibility should be verified for your specific system.
What is the NSN for PWA50671?
PWA50671 is cataloged in the U.S. Government catalog under NSN 5340-00-006-0924. This indicates validated use in U.S. government and defense supply chains.
Community Feedback
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — PWA50671