PartsTable
Technical Data Sheet
Download PDF

PLGA1350010 — PLUG,VENT

✓ Government record, cited
— · ORING SEAL
PRODUCT OVERVIEW

PLGA1350010: PLUG,VENT.

The PLUG,VENT is a the manufacturer industrial component. Key specifications include length: 0.123 INCHES MINIMUM AND 0.132 INCHES MAXIMUM IN, material: ALUMINUM ALLOY, outside_diameter: 0.1341 INCHES MINIMUM AND 0.1350 INCHES MAXIMUM IN, material_document_and_classification: QQ-A-225/6 FED SPEC SINGLE MATERIAL RESPONSE. This part is cataloged in the U.S.

Government catalog under NSN 5340-00-074-2617, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.

Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
PLGA1350010
NSN: 5340-00-074-2617
FSC: 5340 — Hardware, Commercial
CAGE: 92555 — THE LEE CO DBA THE LEE CO (USA)
SPECIFICATIONS
length0.123 INCHES MINIMUM AND 0.132 INCHES MAXIMUM IN
materialALUMINUM ALLOY
outside_diameter0.1341 INCHES MINIMUM AND 0.1350 INCHES MAXIMUM IN
material_document_and_classificationQQ-A-225/6 FED SPEC SINGLE MATERIAL RESPONSE
NSN5340-00-074-2617
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: PLGA1350010 MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
LENGTH: 0.123 INCHES MINIMUM AND 0.132 INCHES MAXIMUM IN
•
MATERIAL DOCUMENT AND CLASSIFICATION: QQ-A-225/6 FED SPEC SINGLE MATERIAL RESPONSE
•
OUTSIDE DIAMETER: 0.1341 INCHES MINIMUM AND 0.1350 INCHES MAXIMUM IN
•
MATERIAL: ALUMINUM ALLOY
TECHNICAL CHARACTERISTICS
LENGTH0.123 INCHES MINIMUM AND 0.132 INCHES MAXIMUM IN
MATERIAL DOCUMENT AND CLASSIFICATIONQQ-A-225/6 FED SPEC SINGLE MATERIAL RESPONSE
OUTSIDE DIAMETER0.1341 INCHES MINIMUM AND 0.1350 INCHES MAXIMUM IN
END ITEM IDENTIFICATIONW/S:HELICOPTER, CH-53A/D/E; HELICOPTER, CHINOOK, CH-47; HELICOPTER, ELECTRONIC COUNTERMEASURES, EH-60A; AIRCRAFT MH-47E SPECIAL OPERATIONS AIRCRAFT; HELICOPTER, BLACK HAWK UH-60A; HELICOPTER, MH53E; AIRCRAFT, HORNET F/A-18; AIRCRAFT, EAGLE F-15 A
MATERIALALUMINUM ALLOY
SUBSTITUTES & CROSS-REFERENCES 5
5900087-3Reference document
Same NSN cross-reference
Reference document — Secondary reference
10117242Reference document
Same NSN cross-reference
Reference document — Informative reference only
572-523-9202Same NSN cross-reference
Same NSN cross-reference
Also cataloged under this NSN
PLGA1350010ASame NSN cross-reference
Same NSN cross-reference
Also cataloged under this NSN
135001Reference document
Same NSN cross-reference
Reference document — Secondary reference
LIFECYCLE
NSN statusActive· U.S. Government catalog
Acquisition advice: Insurance item — stocked against contingency demandNo demilitarization required
Ready to buy PLGA1350010?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is PLGA1350010?
PLGA1350010 is a PLUG,VENT.
What parts can replace PLGA1350010?
There are 5 known substitutes for PLGA1350010: 5900087-3, 10117242, 572-523-9202 and 2 more. Substitute compatibility should be verified for your specific system.
What is the NSN for PLGA1350010?
PLGA1350010 is cataloged in the U.S. Government catalog under NSN 5340-00-074-2617. This indicates validated use in U.S. government and defense supply chains.
Community Feedback
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — PLGA1350010