PartsTable
Technical Data Sheet
Download PDF

N11-6 — GEAR,BEVEL

✓ Government record, cited
— · ORING SEAL
PRODUCT OVERVIEW

N11-6: GEAR,BEVEL.

The GEAR,BEVEL is a the manufacturer industrial component. Key specifications include diameter: 0.204 INCHES NOMINAL IN, material: STEEL COMP 8740 AND STEEL COMP 4037 OVERALL, nut_style: HEXAGON, body_style: PLAIN, SOLID, bore_style: W/ KEYWAY BOTH ENDS, ring_style: CONCENTRIC. This part is cataloged in the U.S.

Government catalog under NSN 5340-00-282-9283, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.

Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
N11-6
NSN: 5340-00-282-9283
NIINs: 002829283, 003505420, 004297492, 004494580, 012355706, 012468451
FSC: 5340 — Hardware, Commercial
CAGE: 81074 — ITT HOLUB INDUSTRIES (USA)
SPECIFICATIONS
diameter0.204 INCHES NOMINAL IN
materialSTEEL COMP 8740 AND STEEL COMP 4037 OVERALL
nut_styleHEXAGON
body_stylePLAIN, SOLID
bore_styleW/ KEYWAY BOTH ENDS
ring_styleCONCENTRIC
teeth_typeSTRAIGHT
joint_styleVERTICAL JOINT
pitch_angle58.0000 DEGREES
temp_rating232.0 CELSIUS NOMINAL DEGC
thread_class3B
overall_width0.1380 INCHES NOMINAL IN
NSN5340-00-282-9283
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: N11-6 MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
STYLE DESIGNATOR: SINGLE LOOP
•
DIAMETER: 0.204 INCHES NOMINAL IN
•
MATERIAL THICKNESS: 0.063 INCHES NOMINAL IN
•
DISTANCE FROM LOOP CENTER TO TONGUE END: 1.125 INCHES NOMINAL IN
•
TONGUE HOLE TYPE: ROUND, UNTHREADED
•
CENTER TO CENTER DISTANCE BETWEEN LOOP AND MOUNTING HOLE: 0.906 INCHES NOMINAL IN
•
MATERIAL: PLASTIC POLYVINYLIDENE CHLORIDE BAND
TECHNICAL CHARACTERISTICS
STYLE DESIGNATORSINGLE LOOP
DIAMETER0.204 INCHES NOMINAL IN
OVERALL WIDTH0.500 INCHES NOMINAL IN
MATERIAL THICKNESS0.063 INCHES NOMINAL IN
DISTANCE FROM LOOP CENTER TO TONGUE END1.125 INCHES NOMINAL IN
TONGUE HOLE TYPEROUND, UNTHREADED
CENTER TO CENTER DISTANCE BETWEEN LOOP AND MOUNTING HOLE0.906 INCHES NOMINAL IN
MATERIALPLASTIC POLYVINYLIDENE CHLORIDE BAND
LOOP INSIDE DIAMETER1.000 INCHES NOMINAL IN
SUBSTITUTES & CROSS-REFERENCES 1
NI16Reference document
Same NSN cross-reference
Reference document — Secondary reference
LIFECYCLE
NSN statusCancelled· U.S. Government catalog
Acquisition advice: Normally procured from the manufacturer (OEM)No demilitarization required
Ready to buy N11-6?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is N11-6?
N11-6 is a GEAR,BEVEL.
What parts can replace N11-6?
There is 1 known substitute for N11-6: NI16. Substitute compatibility should be verified for your specific system.
What is the NSN for N11-6?
N11-6 is cataloged in the U.S. Government catalog under NSN 5340-00-282-9283. This indicates validated use in U.S. government and defense supply chains.
Community Feedback
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — N11-6

✓ PartsTable — the parts reference. Every fact cited to its source.
PartsTable Design LLC · partstable.com
U.S. Government catalog: edition PUBLOGDVD v12.0.0 (OCT 2026), edition date 2026-10-01, retrieved 2026-10-18.
PartsTable commercial catalog: edition Unified commercial catalog snapshot through 2026-09-28, edition date not on file, retrieved 2026-09-28.