PartsTable
Technical Data Sheet
PartsTable / COMPONENT / MS52000-17
MS52000-17 ✓ Verified by PartsTable
— · ORING SEAL
WHAT YOU NEED TO KNOW
Material determines chemical compatibility Standard durometer is 70 Shore A
Wrong material = catastrophic seal failure
PRODUCT OVERVIEW

The GASKET is a the manufacturer industrial component. Key specifications include material: RUBBER CHLOROPRENE CLASS CR OVERALL, hole_diameter: 0.193 INCHES MINIMUM AND 0.213 INCHES MAXIMUM LOCATION NOT OTHERWISE SPECIFIED IN, overall_width: 1.500 INCHES MINIMUM AND 1.516 INCHES MAXIMUM IN, overall_length: 1.500 INCHES MINIMUM AND 1.516 INCHES MAXIMUM IN, hardness_rating: 75.0 SHORE DUROMETER A MINIMUM AND 85.0 SHORE DUROMETER A MAXIMUM OVERALL, style_designator: NON-CIRCULAR. This part is cataloged in the Federal Logistics Information System (FLIS) under NSN 5330-00-968-1753, indicating validated use in U.S.

government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels. Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
MS52000-17
NSN: 5330-00-968-1753
FSC: 5330
CAGE: D9182 — ZF INDUSTRIEANTRIEBE WITTEN GMBH (DEU)
SPECIFICATIONS
materialRUBBER CHLOROPRENE CLASS CR OVERALL
hole_diameter0.193 INCHES MINIMUM AND 0.213 INCHES MAXIMUM LOCATION NOT OTHERWISE SPECIFIED IN
overall_width1.500 INCHES MINIMUM AND 1.516 INCHES MAXIMUM IN
overall_length1.500 INCHES MINIMUM AND 1.516 INCHES MAXIMUM IN
hardness_rating75.0 SHORE DUROMETER A MINIMUM AND 85.0 SHORE DUROMETER A MAXIMUM OVERALL
style_designatorNON-CIRCULAR
aperture_diameter1.250 INCHES MINIMUM AND 1.266 INCHES MAXIMUM IN
bolt_hole_quantity4
outside_corner_radius0.162 INCHES MINIMUM AND 0.182 INCHES MAXIMUM IN
cross-sectional_thickness0.026 INCHES MINIMUM AND 0.036 INCHES MAXIMUM IN
cross-sectional_shape_styleSOLID SINGLE OR COMPOSITION
material_document_and_classificationASTM D2000,2BC815C1E3 ASSN STD SINGLE MATERIAL RESPONSE OVERALL
NSN5330-00-968-1753
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: MS52000-17 MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
HOLE DIAMETER: 0.193 INCHES MINIMUM AND 0.213 INCHES MAXIMUM LOCATION NOT OTHERWISE SPECIFIED IN
•
BOLT HOLE QUANTITY: 4
•
MATERIAL DOCUMENT AND CLASSIFICATION: ASTM D2000,2BC815C1E3 ASSN STD SINGLE MATERIAL RESPONSE OVERALL
•
OUTSIDE CORNER RADIUS: 0.162 INCHES MINIMUM AND 0.182 INCHES MAXIMUM IN
•
CROSS-SECTIONAL THICKNESS: 0.026 INCHES MINIMUM AND 0.036 INCHES MAXIMUM IN
•
STYLE DESIGNATOR: NON-CIRCULAR
•
CENTER TO CENTER DISTANCE BETWEEN BOLT HOLES ALONG LENGTH: 1.146 INCHES MINIMUM AND 1.166 INCHES MAXIMUM LOCATION NOT OTHERWISE SPECIFIED IN
TECHNICAL CHARACTERISTICS (FLIS)
HOLE DIAMETER0.193 INCHES MINIMUM AND 0.213 INCHES MAXIMUM LOCATION NOT OTHERWISE SPECIFIED IN
OVERALL WIDTH1.500 INCHES MINIMUM AND 1.516 INCHES MAXIMUM IN
BOLT HOLE QUANTITY4
MATERIAL DOCUMENT AND CLASSIFICATIONASTM D2000,2BC815C1E3 ASSN STD SINGLE MATERIAL RESPONSE OVERALL
OUTSIDE CORNER RADIUS0.162 INCHES MINIMUM AND 0.182 INCHES MAXIMUM IN
CROSS-SECTIONAL THICKNESS0.026 INCHES MINIMUM AND 0.036 INCHES MAXIMUM IN
STYLE DESIGNATORNON-CIRCULAR
CENTER TO CENTER DISTANCE BETWEEN BOLT HOLES ALONG LENGTH1.146 INCHES MINIMUM AND 1.166 INCHES MAXIMUM LOCATION NOT OTHERWISE SPECIFIED IN
APERTURE DIAMETER1.250 INCHES MINIMUM AND 1.266 INCHES MAXIMUM IN
OUTSIDE EDGE TO BOLT HOLE CENTER DISTANCE ALONG LENGTH0.162 INCHES MINIMUM AND 0.182 INCHES MAXIMUM IN
VERIFIED SUBSTITUTES & CROSS-REFERENCES 34
5330002387383Interchangeable
interchangeable cross-reference
interchangeable
MS52000-1Interchangeable
interchangeable cross-reference
interchangeable
MS52000-6Interchangeable
interchangeable cross-reference
interchangeable
7358504Interchangeable
interchangeable cross-reference
interchangeable
A-A-52481Interchangeable
interchangeable cross-reference
interchangeable
25KP251Interchangeable
interchangeable cross-reference
interchangeable
LIFECYCLE
StatusCANCELLED
Availability—
RoHS CompliantEAR99Not HAZMAT
Ready to buy MS52000-17?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is MS52000-17?
MS52000-17 is a GASKET.
What parts can replace MS52000-17?
There are 34 known substitutes for MS52000-17: 5330002387383, MS52000-1, MS52000-6 and 31 more. Substitute compatibility should be verified for your specific system.
Is MS52000-17 still available?
MS52000-17 is currently cancelled.
Community Feedback
Comments (0)
No comments yet. Be the first to share what you know.
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — MS52000-17

✓ Validated with multiple authoritative sources, including Government, OEM, and Certified sources.
PartsTable Design LLC · partstable.com
Last verified: July 2026