PartsTable
Technical Data Sheet
PartsTable / COMPONENT / MS51007-3
MS51007-3 ✓ Verified by PartsTable
— · ORING SEAL
WHAT YOU NEED TO KNOW
Material determines chemical compatibility Standard durometer is 70 Shore A
Wrong material = catastrophic seal failure
PRODUCT OVERVIEW

The GASKET is a the manufacturer industrial component. Key specifications include material: RUBBER CHLOROPRENE CLASS CR OVERALL, hole_diameter: 0.162 INCHES MINIMUM AND 0.182 INCHES MAXIMUM LOCATION NOT OTHERWISE SPECIFIED IN, overall_width: 1.094 INCHES MINIMUM AND 1.110 INCHES MAXIMUM IN, overall_length: 1.094 INCHES MINIMUM AND 1.110 INCHES MAXIMUM IN, hardness_rating: 45.0 SHORE DUROMETER A MINIMUM AND 55.0 SHORE DUROMETER A MAXIMUM OVERALL, style_designator: NON-CIRCULAR. This product is currently in active production with full OEM support.

This part is cataloged in the Federal Logistics Information System (FLIS) under NSN 5330-00-079-7838, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.

Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
MS51007-3
NSN: 5330-00-079-7838
FSC: 5330
CAGE: D9182 — ZF INDUSTRIEANTRIEBE WITTEN GMBH (DEU)
SPECIFICATIONS
materialRUBBER CHLOROPRENE CLASS CR OVERALL
hole_diameter0.162 INCHES MINIMUM AND 0.182 INCHES MAXIMUM LOCATION NOT OTHERWISE SPECIFIED IN
overall_width1.094 INCHES MINIMUM AND 1.110 INCHES MAXIMUM IN
overall_length1.094 INCHES MINIMUM AND 1.110 INCHES MAXIMUM IN
hardness_rating45.0 SHORE DUROMETER A MINIMUM AND 55.0 SHORE DUROMETER A MAXIMUM OVERALL
style_designatorNON-CIRCULAR
aperture_diameter0.750 INCHES MINIMUM AND 0.766 INCHES MAXIMUM IN
bolt_hole_quantity4
outside_corner_radius0.131 INCHES MINIMUM AND 0.151 INCHES MAXIMUM IN
cross-sectional_thickness0.026 INCHES MINIMUM AND 0.036 INCHES MAXIMUM IN
cross-sectional_shape_styleSOLID SINGLE OR COMPOSITION
material_document_and_classificationASTM D2000 2BC515ABC1F2Z1 ASSN STD SINGLE MATERIAL RESPONSE OVERALL
NSN5330-00-079-7838
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: MS51007-3 MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
CROSS-SECTIONAL SHAPE STYLE: SOLID SINGLE OR COMPOSITION
•
OUTSIDE EDGE TO BOLT HOLE CENTER DISTANCE ALONG LENGTH: 0.131 INCHES MINIMUM AND 0.151 INCHES MAXIMUM IN
•
OUTSIDE EDGE TO BOLT HOLE CENTER DISTANCE ALONG WIDTH: 0.131 INCHES MINIMUM AND 0.151 INCHES MAXIMUM IN
•
HARDNESS RATING: 45.0 SHORE DUROMETER A MINIMUM AND 55.0 SHORE DUROMETER A MAXIMUM OVERALL
•
MATERIAL DOCUMENT AND CLASSIFICATION: ASTM D2000 2BC515ABC1F2Z1 ASSN STD SINGLE MATERIAL RESPONSE OVERALL
•
CENTER TO CENTER DISTANCE BETWEEN BOLT HOLES ALONG LENGTH: 0.803 INCHES MINIMUM AND 0.823 INCHES MAXIMUM LOCATION NOT OTHERWISE SPECIFIED IN
•
CROSS-SECTIONAL THICKNESS: 0.026 INCHES MINIMUM AND 0.036 INCHES MAXIMUM IN
•
MATERIAL: RUBBER CHLOROPRENE CLASS CR OVERALL
TECHNICAL CHARACTERISTICS (FLIS)
CROSS-SECTIONAL SHAPE STYLESOLID SINGLE OR COMPOSITION
OUTSIDE EDGE TO BOLT HOLE CENTER DISTANCE ALONG LENGTH0.131 INCHES MINIMUM AND 0.151 INCHES MAXIMUM IN
OUTSIDE EDGE TO BOLT HOLE CENTER DISTANCE ALONG WIDTH0.131 INCHES MINIMUM AND 0.151 INCHES MAXIMUM IN
HARDNESS RATING45.0 SHORE DUROMETER A MINIMUM AND 55.0 SHORE DUROMETER A MAXIMUM OVERALL
MATERIAL DOCUMENT AND CLASSIFICATIONASTM D2000 2BC515ABC1F2Z1 ASSN STD SINGLE MATERIAL RESPONSE OVERALL
CENTER TO CENTER DISTANCE BETWEEN BOLT HOLES ALONG LENGTH0.803 INCHES MINIMUM AND 0.823 INCHES MAXIMUM LOCATION NOT OTHERWISE SPECIFIED IN
CROSS-SECTIONAL THICKNESS0.026 INCHES MINIMUM AND 0.036 INCHES MAXIMUM IN
MATERIALRUBBER CHLOROPRENE CLASS CR OVERALL
HOLE DIAMETER0.162 INCHES MINIMUM AND 0.182 INCHES MAXIMUM LOCATION NOT OTHERWISE SPECIFIED IN
OVERALL WIDTH1.094 INCHES MINIMUM AND 1.110 INCHES MAXIMUM IN
VERIFIED SUBSTITUTES & CROSS-REFERENCES 21
10266-2Interchangeable
interchangeable cross-reference
interchangeable
8151876-2Interchangeable
interchangeable cross-reference
interchangeable
810G01060Interchangeable
interchangeable cross-reference
interchangeable
6645/BL-95HInterchangeable
interchangeable cross-reference
interchangeable
MA342Interchangeable
interchangeable cross-reference
interchangeable
645GIBInterchangeable
interchangeable cross-reference
interchangeable
LIFECYCLE
StatusACTIVE
AvailabilityOEM and secondary market
RoHS CompliantEAR99Not HAZMAT
Ready to buy MS51007-3?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is MS51007-3?
MS51007-3 is a GASKET.
What parts can replace MS51007-3?
There are 21 known substitutes for MS51007-3: 10266-2, 8151876-2, 810G01060 and 18 more. Substitute compatibility should be verified for your specific system.
What is the NSN for MS51007-3?
MS51007-3 is cataloged in the Federal Logistics Information System (FLIS) under NSN 5330-00-079-7838. This indicates validated use in U.S. government and defense supply chains.
Community Feedback
Comments (0)
No comments yet. Be the first to share what you know.
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — MS51007-3

✓ Validated with multiple authoritative sources, including Government, OEM, and Certified sources.
PartsTable Design LLC · partstable.com
Last verified: July 2026