PartsTable
Technical Data Sheet
Download PDF

MS122910 — CLAMP,LOOP

✓ Government record, cited
— · ORING SEAL
PRODUCT OVERVIEW

MS122910: CLAMP,LOOP.

The CLAMP,LOOP is a the manufacturer industrial component. Key specifications include diameter: 0.199 INCHES MINIMUM AND 0.209 INCHES MAXIMUM IN, material: STEEL COMP 321 BAND, overall_width: 0.484 INCHES MINIMUM AND 0.516 INCHES MAXIMUM IN, style_designator: SINGLE LOOP, tongue_hole_type: ROUND, UNTHREADED, material_thickness: 0.046 INCHES MINIMUM AND 0.056 INCHES MAXIMUM IN. This part is cataloged in the U.S.

Government catalog under NSN 5340-00-598-0234, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.

Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
MS122910
NSN: 5340-00-598-0234
FSC: 5340 — Hardware, Commercial
CAGE: 0U583 — SAE INTERNATIONAL DBA SAE INTERNATIONAL (USA)
SPECIFICATIONS
diameter0.199 INCHES MINIMUM AND 0.209 INCHES MAXIMUM IN
materialSTEEL COMP 321 BAND
overall_width0.484 INCHES MINIMUM AND 0.516 INCHES MAXIMUM IN
style_designatorSINGLE LOOP
tongue_hole_typeROUND, UNTHREADED
material_thickness0.046 INCHES MINIMUM AND 0.056 INCHES MAXIMUM IN
loop_inside_diameter0.750 INCHES NOMINAL IN
material_document_and_classificationAMS 5510 ASSN STD SINGLE MATERIAL RESPONSE BAND
distance_from_loop_center_to_tongue_end0.991 INCHES MINIMUM AND 2.002 INCHES MAXIMUM IN
center_to_center_distance_between_loop_and_mounting_hole0.778 INCHES MINIMUM AND 0.788 INCHES MAXIMUM IN
NSN5340-00-598-0234
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: MS122910 MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
STYLE DESIGNATOR: SINGLE LOOP
•
MATERIAL DOCUMENT AND CLASSIFICATION: AMS 5510 ASSN STD SINGLE MATERIAL RESPONSE BAND
•
DIAMETER: 0.199 INCHES MINIMUM AND 0.209 INCHES MAXIMUM IN
•
MATERIAL THICKNESS: 0.046 INCHES MINIMUM AND 0.056 INCHES MAXIMUM IN
•
DISTANCE FROM LOOP CENTER TO TONGUE END: 0.991 INCHES MINIMUM AND 2.002 INCHES MAXIMUM IN
•
TONGUE HOLE TYPE: ROUND, UNTHREADED
•
CENTER TO CENTER DISTANCE BETWEEN LOOP AND MOUNTING HOLE: 0.778 INCHES MINIMUM AND 0.788 INCHES MAXIMUM IN
TECHNICAL CHARACTERISTICS
STYLE DESIGNATORSINGLE LOOP
MATERIAL DOCUMENT AND CLASSIFICATIONAMS 5510 ASSN STD SINGLE MATERIAL RESPONSE BAND
DIAMETER0.199 INCHES MINIMUM AND 0.209 INCHES MAXIMUM IN
OVERALL WIDTH0.484 INCHES MINIMUM AND 0.516 INCHES MAXIMUM IN
MATERIAL THICKNESS0.046 INCHES MINIMUM AND 0.056 INCHES MAXIMUM IN
DISTANCE FROM LOOP CENTER TO TONGUE END0.991 INCHES MINIMUM AND 2.002 INCHES MAXIMUM IN
TONGUE HOLE TYPEROUND, UNTHREADED
CENTER TO CENTER DISTANCE BETWEEN LOOP AND MOUNTING HOLE0.778 INCHES MINIMUM AND 0.788 INCHES MAXIMUM IN
MATERIALSTEEL COMP 321 BAND
LOOP INSIDE DIAMETER0.750 INCHES NOMINAL IN
OTHER ITEMS IN FSC 5340 — Hardware, Commercial
Items in the same Federal Supply class. No interchangeability or substitution relationship is implied.
5340-00-000-0068 5340-00-000-0132 5340-00-000-8150 5340-00-001-1251 5340-00-001-1264 5340-00-001-1265 5340-00-001-1266 5340-00-001-1275
SUBSTITUTES & CROSS-REFERENCES 1
SAE AS122900 THRU AS122939Reference document
Same NSN cross-reference
Reference document — Design control — primary reference
LIFECYCLE
NSN statusActive· U.S. Government catalog
Acquisition advice: Normally procured from the manufacturer (OEM)No demilitarization required
Ready to buy MS122910?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is MS122910?
MS122910 is a CLAMP,LOOP.
What parts can replace MS122910?
There is 1 known substitute for MS122910: SAE AS122900 THRU AS122939. Substitute compatibility should be verified for your specific system.
What is the NSN for MS122910?
MS122910 is cataloged in the U.S. Government catalog under NSN 5340-00-598-0234. This indicates validated use in U.S. government and defense supply chains.
Community Feedback
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — MS122910