PartsTable
Technical Data Sheet
PartsTable / COMPONENT / MP-0100
MP-0100 ✓ Verified by PartsTable
— · ORING SEAL
WHAT YOU NEED TO KNOW
Material determines chemical compatibility Standard durometer is 70 Shore A
Wrong material = catastrophic seal failure
PRODUCT OVERVIEW

The CLAMP,LOOP is a the manufacturer industrial component. Key specifications include diameter: 0.204 INCHES NOMINAL IN, material: PLASTIC CELLULOSE ACETATE OVERALL, overall_width: 0.500 INCHES NOMINAL IN, style_designator: SINGLE LOOP, tongue_hole_type: ROUND, UNTHREADED, loop_inside_diameter: 0.125 INCHES NOMINAL IN. This product is currently in active production with full OEM support.

This part is cataloged in the Federal Logistics Information System (FLIS) under NSN 5340-01-332-7480, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.

Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
MP-0100
NSN: 5340-01-332-7480
FSC: 5340
CAGE: 14304 — L3HARRIS TECHNOLOGIES, INC. DBA HARRIS CORP DIV HARRIS DEFENSE COMMUNICATIONS (USA)
SPECIFICATIONS
diameter0.204 INCHES NOMINAL IN
materialPLASTIC CELLULOSE ACETATE OVERALL
overall_width0.500 INCHES NOMINAL IN
style_designatorSINGLE LOOP
tongue_hole_typeROUND, UNTHREADED
loop_inside_diameter0.125 INCHES NOMINAL IN
distance_from_loop_center_to_tongue_end0.579 INCHES NOMINAL IN
center_to_center_distance_between_loop_and_mounting_hole0.360 INCHES NOMINAL IN
NSN5340-01-332-7480
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: MP-0100 MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
CENTER TO CENTER DISTANCE BETWEEN LOOP AND MOUNTING HOLE: 0.360 INCHES NOMINAL IN
•
MATERIAL: PLASTIC CELLULOSE ACETATE OVERALL
•
TONGUE HOLE TYPE: ROUND, UNTHREADED
•
LOOP INSIDE DIAMETER: 0.125 INCHES NOMINAL IN
•
STYLE DESIGNATOR: SINGLE LOOP
•
DIAMETER: 0.204 INCHES NOMINAL IN
•
DISTANCE FROM LOOP CENTER TO TONGUE END: 0.579 INCHES NOMINAL IN
TECHNICAL CHARACTERISTICS (FLIS)
CENTER TO CENTER DISTANCE BETWEEN LOOP AND MOUNTING HOLE0.360 INCHES NOMINAL IN
MATERIALPLASTIC CELLULOSE ACETATE OVERALL
TONGUE HOLE TYPEROUND, UNTHREADED
LOOP INSIDE DIAMETER0.125 INCHES NOMINAL IN
STYLE DESIGNATORSINGLE LOOP
DIAMETER0.204 INCHES NOMINAL IN
OVERALL WIDTH0.500 INCHES NOMINAL IN
DISTANCE FROM LOOP CENTER TO TONGUE END0.579 INCHES NOMINAL IN
VERIFIED SUBSTITUTES & CROSS-REFERENCES 12
B1245Interchangeable
interchangeable cross-reference
interchangeable
48-2Interchangeable
interchangeable cross-reference
interchangeable
8925Interchangeable
interchangeable cross-reference
interchangeable
5130-00-242-0614Interchangeable
interchangeable cross-reference
interchangeable
892-5-XInterchangeable
interchangeable cross-reference
interchangeable
8148650Interchangeable
interchangeable cross-reference
interchangeable
LIFECYCLE
StatusACTIVE
AvailabilityOEM and secondary market
RoHS CompliantEAR99Not HAZMAT
Ready to buy MP-0100?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is MP-0100?
MP-0100 is a CLAMP,LOOP.
What parts can replace MP-0100?
There are 12 known substitutes for MP-0100: B1245, 48-2, 8925 and 9 more. Substitute compatibility should be verified for your specific system.
What is the NSN for MP-0100?
MP-0100 is cataloged in the Federal Logistics Information System (FLIS) under NSN 5340-01-332-7480. This indicates validated use in U.S. government and defense supply chains.
Community Feedback
Comments (0)
No comments yet. Be the first to share what you know.
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — MP-0100

✓ Validated with multiple authoritative sources, including Government, OEM, and Certified sources.
PartsTable Design LLC · partstable.com
Last verified: July 2026