PartsTable
Technical Data Sheet
Download PDF

JM44RC2WD4-8 — CLAMP,LOOP

✓ Government record, cited
— · ORING SEAL
PRODUCT OVERVIEW

JM44RC2WD4-8: CLAMP,LOOP.

The CLAMP,LOOP is a the manufacturer industrial component. Key specifications include diameter: 0.194 INCHES MINIMUM AND 0.214 INCHES MAXIMUM IN, material: RUBBER CHLOROPRENE CLASS CR OR RUBBER SYNTHETIC CUSHION, loop_width: 0.250 INCHES NOMINAL IN, loop_length: 0.500 INCHES NOMINAL IN, overall_width: 0.500 INCHES NOMINAL IN, style_designator: RECTANGULAR. This part is cataloged in the U.S.

Government catalog under NSN 5340-01-049-0910, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.

Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
JM44RC2WD4-8
NSN: 5340-01-049-0910
FSC: 5340 — Hardware, Commercial
CAGE: 22175 — J & M PRODUCTS, INC (USA)
SPECIFICATIONS
diameter0.194 INCHES MINIMUM AND 0.214 INCHES MAXIMUM IN
materialRUBBER CHLOROPRENE CLASS CR OR RUBBER SYNTHETIC CUSHION
loop_width0.250 INCHES NOMINAL IN
loop_length0.500 INCHES NOMINAL IN
overall_width0.500 INCHES NOMINAL IN
style_designatorRECTANGULAR
tongue_hole_typeROUND, UNTHREADED
material_thickness0.051 INCHES NOMINAL IN
material_document_and_classificationAMS 3209 ASSN STD 1ST MATERIAL RESPONSE OR SAE SC715 ASSN STD 2ND MATERIAL RESPONSE CUSHION
distance_from_loop_center_to_tongue_end0.958 INCHES NOMINAL IN
center_to_center_distance_between_loop_and_mounting_hole0.740 INCHES NOMINAL IN
NSN5340-01-049-0910
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: JM44RC2WD4-8 MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
LOOP WIDTH: 0.250 INCHES NOMINAL IN
•
STYLE DESIGNATOR: RECTANGULAR
•
MATERIAL DOCUMENT AND CLASSIFICATION: AMS 3209 ASSN STD 1ST MATERIAL RESPONSE OR SAE SC715 ASSN STD 2ND MATERIAL RESPONSE CUSHION
•
DIAMETER: 0.194 INCHES MINIMUM AND 0.214 INCHES MAXIMUM IN
•
MATERIAL THICKNESS: 0.051 INCHES NOMINAL IN
•
DISTANCE FROM LOOP CENTER TO TONGUE END: 0.958 INCHES NOMINAL IN
•
TONGUE HOLE TYPE: ROUND, UNTHREADED
TECHNICAL CHARACTERISTICS
LOOP WIDTH0.250 INCHES NOMINAL IN
STYLE DESIGNATORRECTANGULAR
MATERIAL DOCUMENT AND CLASSIFICATIONAMS 3209 ASSN STD 1ST MATERIAL RESPONSE OR SAE SC715 ASSN STD 2ND MATERIAL RESPONSE CUSHION
DIAMETER0.194 INCHES MINIMUM AND 0.214 INCHES MAXIMUM IN
OVERALL WIDTH0.500 INCHES NOMINAL IN
MATERIAL THICKNESS0.051 INCHES NOMINAL IN
DISTANCE FROM LOOP CENTER TO TONGUE END0.958 INCHES NOMINAL IN
TONGUE HOLE TYPEROUND, UNTHREADED
CENTER TO CENTER DISTANCE BETWEEN LOOP AND MOUNTING HOLE0.740 INCHES NOMINAL IN
MATERIALRUBBER CHLOROPRENE CLASS CR OR RUBBER SYNTHETIC CUSHION
OTHER ITEMS IN FSC 5340 — Hardware, Commercial
Items in the same Federal Supply class. No interchangeability or substitution relationship is implied.
5340-00-000-0068 5340-00-000-0132 5340-00-000-8150 5340-00-001-1251 5340-00-001-1264 5340-00-001-1265 5340-00-001-1266 5340-00-001-1275
SUBSTITUTES & CROSS-REFERENCES 2
202-23506D4W8Reference document
Same NSN cross-reference
Reference document — Vendor item drawing reference
497WD4-8Same NSN cross-reference
Same NSN cross-reference
Also cataloged under this NSN
LIFECYCLE
NSN statusActive· U.S. Government catalog
Acquisition advice: Semi-active item — no replacement plannedNo demilitarization required
Ready to buy JM44RC2WD4-8?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is JM44RC2WD4-8?
JM44RC2WD4-8 is a CLAMP,LOOP.
What parts can replace JM44RC2WD4-8?
There are 2 known substitutes for JM44RC2WD4-8: 202-23506D4W8, 497WD4-8. Substitute compatibility should be verified for your specific system.
What is the NSN for JM44RC2WD4-8?
JM44RC2WD4-8 is cataloged in the U.S. Government catalog under NSN 5340-01-049-0910. This indicates validated use in U.S. government and defense supply chains.
Community Feedback
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — JM44RC2WD4-8