PartsTable
Technical Data Sheet
PartsTable / COMPONENT / GC12A10
GC12A10 ✓ Verified by PartsTable
— · ORING SEAL
WHAT YOU NEED TO KNOW
Material determines chemical compatibility Standard durometer is 70 Shore A
Wrong material = catastrophic seal failure
PRODUCT OVERVIEW

The CLAMP,LOOP is a the manufacturer industrial component. Key specifications include material: STEEL OVERALL, overall_width: 0.312 INCHES NOMINAL IN, special_features: FURNISHED WITH MACHINE SCREW, style_designator: CENTER MOUNT, tongue_hole_type: ROUND, THREADED, surface_treatment: CADMIUM AND CHROMATE OVERALL. This product is currently in active production with full OEM support.

This part is cataloged in the Federal Logistics Information System (FLIS) under NSN 5340-01-164-4559, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.

Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
GC12A10
NSN: 5340-01-164-4559
FSC: 5340
CAGE: 26512 — NORTHROP GRUMMAN SYSTEMS CORPORATION (USA)
SPECIFICATIONS
materialSTEEL OVERALL
overall_width0.312 INCHES NOMINAL IN
special_featuresFURNISHED WITH MACHINE SCREW
style_designatorCENTER MOUNT
tongue_hole_typeROUND, THREADED
surface_treatmentCADMIUM AND CHROMATE OVERALL
material_thickness0.030 INCHES MINIMUM AND 0.034 INCHES MAXIMUM IN
nominal_thread_size0.138 INCHES IN
loop_inside_diameter0.312 INCHES NOMINAL IN
thread_quantity_per_inch32
specification/standard_data17532-GC12 MANUFACTURERS SPECIFICATION
distance_from_loop_center_to_tongue_end0.531 INCHES NOMINAL IN
NSN5340-01-164-4559
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: GC12A10 MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
MATERIAL: STEEL OVERALL
•
SPECIFICATION/STANDARD DATA: 17532-GC12 MANUFACTURERS SPECIFICATION
•
SURFACE TREATMENT DOCUMENT AND CLASSIFICATION: QQ-P-416,TYPE 2 FED SPEC SINGLE TREATMENT RESPONSE OVERALL
•
DISTANCE FROM LOOP CENTER TO TONGUE END: 0.531 INCHES NOMINAL IN
•
LOOP INSIDE DIAMETER: 0.312 INCHES NOMINAL IN
•
CENTER TO CENTER DISTANCE BETWEEN LOOP AND MOUNTING HOLE: 0.344 INCHES NOMINAL IN
•
TONGUE HOLE TYPE: ROUND, THREADED
TECHNICAL CHARACTERISTICS (FLIS)
SPECIAL FEATURESFURNISHED WITH MACHINE SCREW
MATERIALSTEEL OVERALL
SPECIFICATION/STANDARD DATA17532-GC12 MANUFACTURERS SPECIFICATION
SURFACE TREATMENT DOCUMENT AND CLASSIFICATIONQQ-P-416,TYPE 2 FED SPEC SINGLE TREATMENT RESPONSE OVERALL
DISTANCE FROM LOOP CENTER TO TONGUE END0.531 INCHES NOMINAL IN
LOOP INSIDE DIAMETER0.312 INCHES NOMINAL IN
CENTER TO CENTER DISTANCE BETWEEN LOOP AND MOUNTING HOLE0.344 INCHES NOMINAL IN
TONGUE HOLE TYPEROUND, THREADED
MATERIAL THICKNESS0.030 INCHES MINIMUM AND 0.034 INCHES MAXIMUM IN
THREAD QUANTITY PER INCH32
VERIFIED SUBSTITUTES & CROSS-REFERENCES 9
MARUCCI PURE FP (-10)Interchangeable
interchangeable cross-reference
interchangeable
1378357Interchangeable
interchangeable cross-reference
interchangeable
EAA113579Interchangeable
interchangeable cross-reference
interchangeable
SB-10Interchangeable
interchangeable cross-reference
interchangeable
1362214G1Interchangeable
interchangeable cross-reference
interchangeable
SB-100RInterchangeable
interchangeable cross-reference
interchangeable
LIFECYCLE
StatusACTIVE
AvailabilityOEM and secondary market
RoHS CompliantEAR99Not HAZMAT
Ready to buy GC12A10?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is GC12A10?
GC12A10 is a CLAMP,LOOP.
What parts can replace GC12A10?
There are 9 known substitutes for GC12A10: MARUCCI PURE FP (-10), 1378357, EAA113579 and 6 more. Substitute compatibility should be verified for your specific system.
What is the NSN for GC12A10?
GC12A10 is cataloged in the Federal Logistics Information System (FLIS) under NSN 5340-01-164-4559. This indicates validated use in U.S. government and defense supply chains.
Community Feedback
Comments (0)
No comments yet. Be the first to share what you know.
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — GC12A10

✓ Validated with multiple authoritative sources, including Government, OEM, and Certified sources.
PartsTable Design LLC · partstable.com
Last verified: July 2026