PartsTable
Technical Data Sheet
Download PDF

G167957 — CLIP,SPRING TENSION

✓ Government record, cited
— · ORING SEAL
PRODUCT OVERVIEW

G167957: CLIP,SPRING TENSION.

The CLIP,SPRING TENSION is a the manufacturer industrial component. Key specifications include width: 0.125 INCHES NOMINAL IN, length: 0.195 INCHES NOMINAL IN, material: COPPER ALLOY OVERALL, hole_diameter: 0.064 INCHES MINIMUM AND 0.680 INCHES MAXIMUM IN, overall_height: 0.250 INCHES NOMINAL IN, mounting_method: UNTHREADED HOLE(S). This part is cataloged in the U.S.

Government catalog under NSN 5340-01-058-8827, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.

Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
G167957
NSN: 5340-01-058-8827
FSC: 5340 — Hardware, Commercial
CAGE: 3B150 — RAYTHEON COMPANY DBA RAYTHEON CO (USA)
SPECIFICATIONS
width0.125 INCHES NOMINAL IN
length0.195 INCHES NOMINAL IN
materialCOPPER ALLOY OVERALL
hole_diameter0.064 INCHES MINIMUM AND 0.680 INCHES MAXIMUM IN
overall_height0.250 INCHES NOMINAL IN
mounting_methodUNTHREADED HOLE(S)
surface_treatmentTIN OVERALL
material_thickness0.009 INCHES MINIMUM AND 0.012 INCHES MAXIMUM IN
loop/holding_dimension0.170 INCHES MINIMUM AND 0.185 INCHES MAXIMUM IN
distance_from_loop_center_to_end0.150 INCHES NOMINAL IN
surface_treatment_document_and_classificationMIL-T-10727,TYPE 1 MIL SPEC SINGLE TREATMENT RESPONSE OVERALL
NSN5340-01-058-8827
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: G167957 MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
LENGTH: 0.195 INCHES NOMINAL IN
•
SURFACE TREATMENT DOCUMENT AND CLASSIFICATION: MIL-T-10727,TYPE 1 MIL SPEC SINGLE TREATMENT RESPONSE OVERALL
•
MOUNTING METHOD: UNTHREADED HOLE(S)
•
LOOP/HOLDING DIMENSION: 0.170 INCHES MINIMUM AND 0.185 INCHES MAXIMUM IN
•
MATERIAL THICKNESS: 0.009 INCHES MINIMUM AND 0.012 INCHES MAXIMUM IN
•
DISTANCE FROM LOOP CENTER TO END: 0.150 INCHES NOMINAL IN
•
SURFACE TREATMENT: TIN OVERALL
TECHNICAL CHARACTERISTICS
OVERALL HEIGHT0.250 INCHES NOMINAL IN
LENGTH0.195 INCHES NOMINAL IN
SURFACE TREATMENT DOCUMENT AND CLASSIFICATIONMIL-T-10727,TYPE 1 MIL SPEC SINGLE TREATMENT RESPONSE OVERALL
MOUNTING METHODUNTHREADED HOLE(S)
LOOP/HOLDING DIMENSION0.170 INCHES MINIMUM AND 0.185 INCHES MAXIMUM IN
MATERIAL THICKNESS0.009 INCHES MINIMUM AND 0.012 INCHES MAXIMUM IN
DISTANCE FROM LOOP CENTER TO END0.150 INCHES NOMINAL IN
SURFACE TREATMENTTIN OVERALL
WIDTH0.125 INCHES NOMINAL IN
MATERIALCOPPER ALLOY OVERALL
SUBSTITUTES & CROSS-REFERENCES 3
6015-27CTReference document
Same NSN cross-reference
Reference document — Secondary reference
1133030Same NSN cross-reference
Same NSN cross-reference
Also cataloged under this NSN
1133030G1Reference document
Same NSN cross-reference
Reference document — Design control — primary reference
LIFECYCLE
NSN statusActive· U.S. Government catalog
Acquisition advice: Normally procured from the manufacturer (OEM)No demilitarization required
Ready to buy G167957?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is G167957?
G167957 is a CLIP,SPRING TENSION.
What parts can replace G167957?
There are 3 known substitutes for G167957: 6015-27CT, 1133030, 1133030G1. Substitute compatibility should be verified for your specific system.
What is the NSN for G167957?
G167957 is cataloged in the U.S. Government catalog under NSN 5340-01-058-8827. This indicates validated use in U.S. government and defense supply chains.
Community Feedback
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — G167957