PartsTable
Technical Data Sheet
Download PDF

EW1 3-8 — BEARING,BALL,THRUST

✓ Government record, cited
— · TAPERED BEARING
PRODUCT OVERVIEW

EW1 3-8: BEARING,BALL,THRUST.

The BEARING,BALL,THRUST is a the manufacturer industrial component. Key specifications include material: STEEL WASHER, alignment_type: RIGID, overall_height: 0.5000 INCHES NOMINAL IN, surface_finish: GROUND, style_designator: FLAT RACE SURFACE, IN LINE BALL RETAINER, bore_smallest_diameter: 1.3750 INCHES NOMINAL IN. This part is cataloged in the U.S.

Government catalog under NSN 3110-00-155-9122, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.

Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
EW1 3-8
NSN: 3110-00-155-9122
FSC: 3110 — Bearings, Antifriction, Unmounted
CAGE: 43991 — FAG BEARINGS CORPORATION (USA)
SPECIFICATIONS
materialSTEEL WASHER
alignment_typeRIGID
overall_height0.5000 INCHES NOMINAL IN
surface_finishGROUND
style_designatorFLAT RACE SURFACE, IN LINE BALL RETAINER
bore_smallest_diameter1.3750 INCHES NOMINAL IN
overall_outside_diameter2.1875 INCHES NOMINAL IN
standard_tolerance_designationABEC NO.1
thrust_directional_capability_designationSINGLE
NSN3110-00-155-9122
COMPONENT DIAGRAM
TAPERED ROLLER BEARING — CUP & CONE ASSEMBLY CAGE CUP BORE CONE OD: — · BORE: — · WIDTH: — Single Row · PN: EW1 3-8 · OEM ⚠ VERIFY BEFORE ORDERING Cup and cone sold separately — verify you are ordering BOTH parts or the correct component. Always replace cup and cone together — mismatched wear = premature failure ✓ BROKER TIP Taper angle determines axial load capacity. Steeper angle = higher axial load rating. Timken series numbers indicate dimensions — cross-reference carefully PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
SURFACE FINISH: GROUND
•
STYLE DESIGNATOR: FLAT RACE SURFACE, IN LINE BALL RETAINER
•
THRUST DIRECTIONAL CAPABILITY DESIGNATION: SINGLE
•
OVERALL OUTSIDE DIAMETER: 2.1875 INCHES NOMINAL IN
•
BORE SMALLEST DIAMETER: 1.3750 INCHES NOMINAL IN
•
ALIGNMENT TYPE: RIGID
•
STANDARD TOLERANCE DESIGNATION: ABEC NO.1
TECHNICAL CHARACTERISTICS
OVERALL HEIGHT0.5000 INCHES NOMINAL IN
SURFACE FINISHGROUND
STYLE DESIGNATORFLAT RACE SURFACE, IN LINE BALL RETAINER
THRUST DIRECTIONAL CAPABILITY DESIGNATIONSINGLE
OVERALL OUTSIDE DIAMETER2.1875 INCHES NOMINAL IN
BORE SMALLEST DIAMETER1.3750 INCHES NOMINAL IN
ALIGNMENT TYPERIGID
STANDARD TOLERANCE DESIGNATIONABEC NO.1
MATERIALSTEEL OR STEEL CORROSION RESISTING RETAINER
MATERIALSTEEL BALL
SUBSTITUTES & CROSS-REFERENCES 2
144-449Same NSN cross-reference
Same NSN cross-reference
Also cataloged under this NSN
FT1 3/8Same NSN cross-reference
Same NSN cross-reference
Also cataloged under this NSN
LIFECYCLE
NSN statusActive· U.S. Government catalog
Acquisition advice: Normally procured from the manufacturer (OEM)No demilitarization required
Ready to buy EW1 3-8?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is EW1 3-8?
EW1 3-8 is a BEARING,BALL,THRUST.
What parts can replace EW1 3-8?
There are 2 known substitutes for EW1 3-8: 144-449, FT1 3/8. Substitute compatibility should be verified for your specific system.
What is the NSN for EW1 3-8?
EW1 3-8 is cataloged in the U.S. Government catalog under NSN 3110-00-155-9122. This indicates validated use in U.S. government and defense supply chains.
Community Feedback
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — EW1 3-8