PartsTable
Technical Data Sheet
Download PDF

C01J10118-3 — RING,BEARING,INNER

✓ Government record, cited
— · TAPERED BEARING
PRODUCT OVERVIEW

C01J10118-3: RING,BEARING,INNER.

The RING,BEARING,INNER is a the manufacturer industrial component. Key specifications include material: PLASTIC POLYTETRAFLUOROETHYLENE SINGLE COMPONENT THIRD PRIMARY, overall_width: 1.50 INCHES NOMINAL IN, special_features: EIGHT HOLES DIAMETER 0.625 , FIVE HOLES DIAMETER 0.221 AL, end_item_identification: 2330-01627-2944, retainer_fabrication_method: MOLDED, part_name_assigned_by_controlling_agency: BEARING INNER. This part is cataloged in the U.S.

Government catalog under NSN 3110-01-733-2534, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.

Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
C01J10118-3
NSN: 3110-01-733-2534
NIINs: 017332534, 017332543
FSC: 3110 — Bearings, Antifriction, Unmounted
CAGE: 01365 — MARINE CORPS SYSTEMS COMMAND DIV MARINE CORPS SYSTEMS COMMAND TECHNICAL DATA REPOSITORY CUSTOMER SERVICE (USA)
SPECIFICATIONS
materialPLASTIC POLYTETRAFLUOROETHYLENE SINGLE COMPONENT THIRD PRIMARY
overall_width1.50 INCHES NOMINAL IN
special_featuresEIGHT HOLES DIAMETER 0.625 , FIVE HOLES DIAMETER 0.221 AL
end_item_identification2330-01627-2944
retainer_fabrication_methodMOLDED
part_name_assigned_by_controlling_agencyBEARING INNER
NSN3110-01-733-2534
COMPONENT DIAGRAM
TAPERED ROLLER BEARING — CUP & CONE ASSEMBLY CAGE CUP BORE CONE OD: — · BORE: — · WIDTH: — Single Row · PN: C01J10118-3 · OEM ⚠ VERIFY BEFORE ORDERING Cup and cone sold separately — verify you are ordering BOTH parts or the correct component. Always replace cup and cone together — mismatched wear = premature failure ✓ BROKER TIP Taper angle determines axial load capacity. Steeper angle = higher axial load rating. Timken series numbers indicate dimensions — cross-reference carefully PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
RETAINER FABRICATION METHOD: MOLDED
•
MATERIAL: PLASTIC POLYTETRAFLUOROETHYLENE SINGLE COMPONENT THIRD PRIMARY
TECHNICAL CHARACTERISTICS
RETAINER FABRICATION METHODMOLDED
OVERALL WIDTH1.50 INCHES NOMINAL IN
SPECIAL FEATURESEIGHT HOLES DIAMETER 0.625 , FIVE HOLES DIAMETER 0.221 AL
PART NAME ASSIGNED BY CONTROLLING AGENCYBEARING INNER
END ITEM IDENTIFICATION2330-01627-2944
MATERIALPLASTIC POLYTETRAFLUOROETHYLENE SINGLE COMPONENT THIRD PRIMARY
SUBSTITUTES & CROSS-REFERENCES 1
C01J10118Reference document
Same NSN cross-reference
Reference document — Drawing number reference only
LIFECYCLE
NSN statusActive· U.S. Government catalog
Acquisition advice: Normally procured from the manufacturer (OEM)No demilitarization required
Ready to buy C01J10118-3?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is C01J10118-3?
C01J10118-3 is a RING,BEARING,INNER.
What parts can replace C01J10118-3?
There is 1 known substitute for C01J10118-3: C01J10118. Substitute compatibility should be verified for your specific system.
What is the NSN for C01J10118-3?
C01J10118-3 is cataloged in the U.S. Government catalog under NSN 3110-01-733-2534. This indicates validated use in U.S. government and defense supply chains.
Community Feedback
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — C01J10118-3