PartsTable
Technical Data Sheet
PartsTable / COMPONENT / BACC10DK5
BACC10DK5 ✓ Verified by PartsTable
— · ORING SEAL
WHAT YOU NEED TO KNOW
Material determines chemical compatibility Standard durometer is 70 Shore A
Wrong material = catastrophic seal failure
PRODUCT OVERVIEW

The CLAMP,LOOP is a the manufacturer industrial component. Key specifications include diameter: 0.198 INCHES MINIMUM AND 0.213 INCHES MAXIMUM IN, material: PLASTIC POLYHEXAMETHYLENE AMIDE OVERALL, overall_width: 0.485 INCHES MINIMUM AND 0.515 INCHES MAXIMUM IN, style_designator: SINGLE LOOP, tongue_hole_type: ROUND, UNTHREADED, material_thickness: 0.045 INCHES MINIMUM AND 0.060 INCHES MAXIMUM IN. This part is cataloged in the Federal Logistics Information System (FLIS) under NSN 5340-00-834-8789, indicating validated use in U.S.

government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels. Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
BACC10DK5
NSN: 5340-00-834-8789
FSC: 5340
CAGE: 81872 — OLYMPIC PLASTICS CO SUBSIDIARY OF INTERCONTINENTAL DIAMOND CORP (USA)
SPECIFICATIONS
diameter0.198 INCHES MINIMUM AND 0.213 INCHES MAXIMUM IN
materialPLASTIC POLYHEXAMETHYLENE AMIDE OVERALL
overall_width0.485 INCHES MINIMUM AND 0.515 INCHES MAXIMUM IN
style_designatorSINGLE LOOP
tongue_hole_typeROUND, UNTHREADED
material_thickness0.045 INCHES MINIMUM AND 0.060 INCHES MAXIMUM IN
loop_inside_diameter0.312 INCHES NOMINAL IN
material_document_and_classificationASTM D4066 ASSN STD SINGLE MATERIAL RESPONSE OVERALL
distance_from_loop_center_to_tongue_end0.810 INCHES NOMINAL IN
center_to_center_distance_between_loop_and_mounting_hole0.535 INCHES MINIMUM AND 0.585 INCHES MAXIMUM IN
NSN5340-00-834-8789
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: BACC10DK5 MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
MATERIAL: PLASTIC POLYHEXAMETHYLENE AMIDE OVERALL
•
MATERIAL DOCUMENT AND CLASSIFICATION: ASTM D4066 ASSN STD SINGLE MATERIAL RESPONSE OVERALL
•
LOOP INSIDE DIAMETER: 0.312 INCHES NOMINAL IN
•
TONGUE HOLE TYPE: ROUND, UNTHREADED
•
DISTANCE FROM LOOP CENTER TO TONGUE END: 0.810 INCHES NOMINAL IN
•
CENTER TO CENTER DISTANCE BETWEEN LOOP AND MOUNTING HOLE: 0.535 INCHES MINIMUM AND 0.585 INCHES MAXIMUM IN
•
MATERIAL THICKNESS: 0.045 INCHES MINIMUM AND 0.060 INCHES MAXIMUM IN
TECHNICAL CHARACTERISTICS (FLIS)
OVERALL WIDTH0.485 INCHES MINIMUM AND 0.515 INCHES MAXIMUM IN
MATERIALPLASTIC POLYHEXAMETHYLENE AMIDE OVERALL
MATERIAL DOCUMENT AND CLASSIFICATIONASTM D4066 ASSN STD SINGLE MATERIAL RESPONSE OVERALL
LOOP INSIDE DIAMETER0.312 INCHES NOMINAL IN
TONGUE HOLE TYPEROUND, UNTHREADED
DISTANCE FROM LOOP CENTER TO TONGUE END0.810 INCHES NOMINAL IN
CENTER TO CENTER DISTANCE BETWEEN LOOP AND MOUNTING HOLE0.535 INCHES MINIMUM AND 0.585 INCHES MAXIMUM IN
MATERIAL THICKNESS0.045 INCHES MINIMUM AND 0.060 INCHES MAXIMUM IN
DIAMETER0.198 INCHES MINIMUM AND 0.213 INCHES MAXIMUM IN
STYLE DESIGNATORSINGLE LOOP
VERIFIED SUBSTITUTES & CROSS-REFERENCES 23
SAE-AS7351Upgraded Successor
successor cross-reference
successor
AN735D28Upgraded Successor
successor cross-reference
successor
AN735-6Upgraded Successor
successor cross-reference
successor
AN735D40Upgraded Successor
successor cross-reference
successor
AN735D32Upgraded Successor
successor cross-reference
successor
5342PL0196422Upgraded Successor
successor cross-reference
successor
LIFECYCLE
StatusCANCELLED
Availability—
RoHS CompliantEAR99Not HAZMAT
Ready to buy BACC10DK5?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is BACC10DK5?
BACC10DK5 is a CLAMP,LOOP.
What parts can replace BACC10DK5?
There are 23 known substitutes for BACC10DK5: SAE-AS7351, AN735D28, AN735-6 and 20 more. Substitute compatibility should be verified for your specific system.
Is BACC10DK5 still available?
BACC10DK5 is currently cancelled.
Community Feedback
Comments (0)
No comments yet. Be the first to share what you know.
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — BACC10DK5

✓ Validated with multiple authoritative sources, including Government, OEM, and Certified sources.
PartsTable Design LLC · partstable.com
Last verified: July 2026