PartsTable
Technical Data Sheet
Download PDF

AS7351-44 — CLAMP,LOOP

✓ Government record, cited
— · ORING SEAL
PRODUCT OVERVIEW

AS7351-44: CLAMP,LOOP.

The CLAMP,LOOP is a the manufacturer industrial component. Key specifications include diameter: 0.204 INCHES NOMINAL IN, material: STEEL BAND, overall_width: 0.375 INCHES NOMINAL IN, style_designator: CENTER MOUNT, tongue_hole_type: ROUND, UNTHREADED, surface_treatment: CADMIUM OR ZINC BAND. This part is cataloged in the U.S.

Government catalog under NSN 5340-00-193-0153, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.

Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
AS7351-44
NSN: 5340-00-193-0153
FSC: 5340 — Hardware, Commercial
CAGE: 0U583 — SAE INTERNATIONAL DBA SAE INTERNATIONAL (USA)
SPECIFICATIONS
diameter0.204 INCHES NOMINAL IN
materialSTEEL BAND
overall_width0.375 INCHES NOMINAL IN
style_designatorCENTER MOUNT
tongue_hole_typeROUND, UNTHREADED
surface_treatmentCADMIUM OR ZINC BAND
material_thickness0.031 INCHES NOMINAL IN
loop_inside_diameter2.750 INCHES NOMINAL IN
distance_from_loop_center_to_tongue_end1.875 INCHES NOMINAL IN
center_to_center_distance_between_loop_and_mounting_hole1.687 INCHES NOMINAL IN
NSN5340-00-193-0153
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: AS7351-44 MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
STYLE DESIGNATOR: CENTER MOUNT
•
DIAMETER: 0.204 INCHES NOMINAL IN
•
MATERIAL THICKNESS: 0.031 INCHES NOMINAL IN
•
DISTANCE FROM LOOP CENTER TO TONGUE END: 1.875 INCHES NOMINAL IN
•
SURFACE TREATMENT: CADMIUM OR ZINC BAND
•
TONGUE HOLE TYPE: ROUND, UNTHREADED
•
CENTER TO CENTER DISTANCE BETWEEN LOOP AND MOUNTING HOLE: 1.687 INCHES NOMINAL IN
TECHNICAL CHARACTERISTICS
STYLE DESIGNATORCENTER MOUNT
DIAMETER0.204 INCHES NOMINAL IN
OVERALL WIDTH0.375 INCHES NOMINAL IN
MATERIAL THICKNESS0.031 INCHES NOMINAL IN
DISTANCE FROM LOOP CENTER TO TONGUE END1.875 INCHES NOMINAL IN
SURFACE TREATMENTCADMIUM OR ZINC BAND
TONGUE HOLE TYPEROUND, UNTHREADED
CENTER TO CENTER DISTANCE BETWEEN LOOP AND MOUNTING HOLE1.687 INCHES NOMINAL IN
MATERIALSTEEL BAND
LOOP INSIDE DIAMETER2.750 INCHES NOMINAL IN
SUBSTITUTES & CROSS-REFERENCES 2
AN735-44Reference document
Same NSN cross-reference
Reference document — Secondary reference
SAE-AS7351Reference document
Same NSN cross-reference
Reference document — Design control — primary reference
LIFECYCLE
NSN statusActive· U.S. Government catalog
Acquisition advice: Normally procured from the manufacturer (OEM)No demilitarization required
Ready to buy AS7351-44?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is AS7351-44?
AS7351-44 is a CLAMP,LOOP.
What parts can replace AS7351-44?
There are 2 known substitutes for AS7351-44: AN735-44, SAE-AS7351. Substitute compatibility should be verified for your specific system.
What is the NSN for AS7351-44?
AS7351-44 is cataloged in the U.S. Government catalog under NSN 5340-00-193-0153. This indicates validated use in U.S. government and defense supply chains.
Community Feedback
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — AS7351-44

✓ PartsTable — the parts reference. Every fact cited to its source.
PartsTable Design LLC · partstable.com
U.S. Government catalog: edition PUBLOGDVD v12.0.0 (OCT 2026), edition date 2026-10-01, retrieved 2026-10-18.
PartsTable commercial catalog: edition Unified commercial catalog snapshot through 2026-09-28, edition date not on file, retrieved 2026-09-28.