PartsTable
Technical Data Sheet
Download PDF

AS114-S59-70 — O-RING

✓ Government record, cited
— · ORING SEAL
PRODUCT OVERVIEW

AS114-S59-70: O-RING.

The O-RING is a the manufacturer industrial component. Key specifications include material: RUBBER SILICONE CLASS Q, hardness_rating: 65.0 SHORE DUROMETER A MINIMUM AND 75.0 SHORE DUROMETER A MAXIMUM, center_hole_diameter: 0.603 INCHES MINIMUM AND 0.621 INCHES MAXIMUM IN, cross-sectional_height: 0.100 INCHES MINIMUM AND 0.106 INCHES MAXIMUM IN. This part is cataloged in the U.S.

Government catalog under NSN 5331-01-387-6319, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.

Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
AS114-S59-70
NSN: 5331-01-387-6319
FSC: 5331 — O-ring
CAGE: 76680 — FEDERAL-MOGUL CORP CHASSIS PRODUCTS DIV (USA)
SPECIFICATIONS
materialRUBBER SILICONE CLASS Q
hardness_rating65.0 SHORE DUROMETER A MINIMUM AND 75.0 SHORE DUROMETER A MAXIMUM
center_hole_diameter0.603 INCHES MINIMUM AND 0.621 INCHES MAXIMUM IN
cross-sectional_height0.100 INCHES MINIMUM AND 0.106 INCHES MAXIMUM IN
NSN5331-01-387-6319
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: AS114-S59-70 MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
CROSS-SECTIONAL HEIGHT: 0.100 INCHES MINIMUM AND 0.106 INCHES MAXIMUM IN
•
HARDNESS RATING: 65.0 SHORE DUROMETER A MINIMUM AND 75.0 SHORE DUROMETER A MAXIMUM
•
CENTER HOLE DIAMETER: 0.603 INCHES MINIMUM AND 0.621 INCHES MAXIMUM IN
•
MATERIAL: RUBBER SILICONE CLASS Q
TECHNICAL CHARACTERISTICS
CROSS-SECTIONAL HEIGHT0.100 INCHES MINIMUM AND 0.106 INCHES MAXIMUM IN
HARDNESS RATING65.0 SHORE DUROMETER A MINIMUM AND 75.0 SHORE DUROMETER A MAXIMUM
CENTER HOLE DIAMETER0.603 INCHES MINIMUM AND 0.621 INCHES MAXIMUM IN
MATERIALRUBBER SILICONE CLASS Q
SUBSTITUTES & CROSS-REFERENCES 2
2-114S604-70Reference document
Same NSN cross-reference
Reference document — Secondary reference
B86002-114SSame NSN cross-reference
Same NSN cross-reference
Also cataloged under this NSN
LIFECYCLE
NSN statusActive· U.S. Government catalog
Acquisition advice: Normally procured from the manufacturer (OEM)No demilitarization required
Ready to buy AS114-S59-70?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is AS114-S59-70?
AS114-S59-70 is a O-RING.
What parts can replace AS114-S59-70?
There are 2 known substitutes for AS114-S59-70: 2-114S604-70, B86002-114S. Substitute compatibility should be verified for your specific system.
What is the NSN for AS114-S59-70?
AS114-S59-70 is cataloged in the U.S. Government catalog under NSN 5331-01-387-6319. This indicates validated use in U.S. government and defense supply chains.
Community Feedback
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — AS114-S59-70

✓ PartsTable — the parts reference. Every fact cited to its source.
PartsTable Design LLC · partstable.com
U.S. Government catalog: edition PUBLOGDVD v12.0.0 (OCT 2026), edition date 2026-10-01, retrieved 2026-10-18.
PartsTable commercial catalog: edition Unified commercial catalog snapshot through 2026-09-28, edition date not on file, retrieved 2026-09-28.