PartsTable
Technical Data Sheet
PartsTable / MRO / A0-16
A0-16 ✓ Verified by PartsTable
— · MRO · MRO_GENERAL
WHAT YOU NEED TO KNOW
Material determines chemical compatibility Standard durometer is 70 Shore A
Wrong material = catastrophic seal failure
PRODUCT OVERVIEW

RESISTOR,VARIABLE,WIRE WOUND,PRE. Key specifications include material: RUBBER, base_style: WIRE LEADS, DOWN, body_style: CYLINDRICAL SERVO MOUNTED, bulb_style: T (TUBULAR), body_length: 2.438 INCHES NOMINAL IN, shaft_style: ROUND. This product is currently in active production with full OEM support.

This part is cataloged in the Federal Logistics Information System (FLIS) under NSN 5331-00-069-9103, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.

Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
MRO→ MRO_GENERAL→ A0-16
NSN: 5331-00-069-9103
FSC: 5331 — O-RING
CAGE: 09990 — PARKER-HANNIFIN CORPORATION DBA PNEUTRONICS DIV HYDRAULIC VALVE DIVISION (USA)
SPECIFICATIONS
materialRUBBER
base_styleWIRE LEADS, DOWN
body_styleCYLINDRICAL SERVO MOUNTED
bulb_styleT (TUBULAR)
body_length2.438 INCHES NOMINAL IN
shaft_styleROUND
pilot_length0.0620 INCHES NOMINAL IN
shaft_length0.750 INCHES NOMINAL IN
shaft_runout0.002 INCHES IN
actuator_typeSINGLE SHAFT
body_diameter1.875 INCHES NOMINAL IN
alignment_typeRIGID
NSN5331-00-069-9103
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: A0-16 MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
MATERIAL: RUBBER SYNTHETIC
•
CENTER HOLE DIAMETER: 0.609 INCHES MINIMUM AND 0.619 INCHES MAXIMUM IN
•
CROSS-SECTIONAL HEIGHT: 0.067 INCHES MINIMUM AND 0.073 INCHES MAXIMUM IN
TECHNICAL CHARACTERISTICS (FLIS)
MATERIALRUBBER SYNTHETIC
CENTER HOLE DIAMETER0.609 INCHES MINIMUM AND 0.619 INCHES MAXIMUM IN
CROSS-SECTIONAL HEIGHT0.067 INCHES MINIMUM AND 0.073 INCHES MAXIMUM IN
VERIFIED SUBSTITUTES & CROSS-REFERENCES 9
92296Interchangeable
interchangeable cross-reference
interchangeable
21557Interchangeable
interchangeable cross-reference
interchangeable
A016Interchangeable
interchangeable cross-reference
interchangeable
SCB422035Interchangeable
interchangeable cross-reference
interchangeable
A016-CNInterchangeable
interchangeable cross-reference
interchangeable
2140-0013Interchangeable
interchangeable cross-reference
interchangeable
LIFECYCLE
StatusACTIVE
AvailabilityOEM and secondary market
RoHS CompliantEAR99Not HAZMAT
Ready to buy A0-16?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is A0-16?
A0-16 is a RESISTOR,VARIABLE,WIRE WOUND,PRE. It is classified as a MRO (MRO_GENERAL).
What parts can replace A0-16?
There are 9 known substitutes for A0-16: 92296, 21557, A016 and 6 more. Substitute compatibility should be verified for your specific system.
What is the NSN for A0-16?
A0-16 is cataloged in the Federal Logistics Information System (FLIS) under NSN 5331-00-069-9103. This indicates validated use in U.S. government and defense supply chains.
Community Feedback
Comments (0)
No comments yet. Be the first to share what you know.
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — A0-16

✓ Validated with multiple authoritative sources, including Government, OEM, and Certified sources.
PartsTable Design LLC · partstable.com
Last verified: July 2026