PartsTable
Technical Data Sheet
PartsTable / MRO / A-7196
A-7196 ✓ Verified by PartsTable
— · MRO · MRO_GENERAL
WHAT YOU NEED TO KNOW
Material determines chemical compatibility Standard durometer is 70 Shore A
Wrong material = catastrophic seal failure
PRODUCT OVERVIEW

RESISTOR,FIXED,WIRE WOUND,INDUCT. Key specifications include material: COTTON AND PLASTIC PHENOLIC OVERALL, body_length: 0.906 INCHES MINIMUM AND 1.094 INCHES MAXIMUM IN, corner_shape: SQUARE INSIDE RIGHT CORNER, flange_width: 0.0950 INCHES NOMINAL IN, body_diameter: 0.250 INCHES MINIMUM AND 0.376 INCHES MAXIMUM IN, cubic_measure: 0.100 CUBIC INCHES. This product is currently in active production with full OEM support.

This part is cataloged in the Federal Logistics Information System (FLIS) under NSN 5330-00-016-6320, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.

Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
MRO→ MRO_GENERAL→ A-7196
NSN: 5330-00-016-6320
FSC: 5330
CAGE: 83259 — PARKER-HANNIFIN CORPORATION DBA PNEUTRONICS DIV COMPOSITE SEALING SYSTEMS DIVISION (USA)
SPECIFICATIONS
materialCOTTON AND PLASTIC PHENOLIC OVERALL
body_length0.906 INCHES MINIMUM AND 1.094 INCHES MAXIMUM IN
corner_shapeSQUARE INSIDE RIGHT CORNER
flange_width0.0950 INCHES NOMINAL IN
body_diameter0.250 INCHES MINIMUM AND 0.376 INCHES MAXIMUM IN
cubic_measure0.100 CUBIC INCHES
hole_diameter0.328 INCHES NOMINAL LOCATION NOT OTHERWISE SPECIFIED IN
overall_width4.530 INCHES NOMINAL IN
terminal_typeWIRE LEAD
inclosure_typeENCAPSULATED
overall_length0.5312 INCHES NOMINAL IN
terminal_length1.375 INCHES MINIMUM AND 2.125 INCHES MAXIMUM IN
NSN5330-00-016-6320
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: A-7196 MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
OUTSIDE CORNER INVERTED RADIUS: 0.375 INCHES NOMINAL IN
•
GAGE RING THICKNESS: 0.920 INCHES NOMINAL IN
•
CROSS-SECTIONAL THICKNESS: 0.132 INCHES NOMINAL IN
•
CROSS-SECTIONAL SHAPE STYLE: METAL AND SYNTHETIC RUBBER
•
MATERIAL DOCUMENT AND CLASSIFICATION: QQ-A-250/5 T4 FED SPEC SINGLE MATERIAL RESPONSE OVERALL
•
SIDE RADIUS FROM GASKET CENTER: 1.875 INCHES NOMINAL IN
•
BOLT CIRCLE DIAMETER: 4.312 INCHES NOMINAL IN
TECHNICAL CHARACTERISTICS (FLIS)
OUTSIDE CORNER INVERTED RADIUS0.375 INCHES NOMINAL IN
GAGE RING THICKNESS0.920 INCHES NOMINAL IN
CROSS-SECTIONAL THICKNESS0.132 INCHES NOMINAL IN
CROSS-SECTIONAL SHAPE STYLEMETAL AND SYNTHETIC RUBBER
MATERIAL DOCUMENT AND CLASSIFICATIONQQ-A-250/5 T4 FED SPEC SINGLE MATERIAL RESPONSE OVERALL
OVERALL WIDTH4.530 INCHES NOMINAL IN
SIDE RADIUS FROM GASKET CENTER1.875 INCHES NOMINAL IN
BOLT CIRCLE DIAMETER4.312 INCHES NOMINAL IN
OUTSIDE CORNER RADIUS0.375 INCHES NOMINAL IN
HOLE DIAMETER0.328 INCHES NOMINAL LOCATION NOT OTHERWISE SPECIFIED IN
VERIFIED SUBSTITUTES & CROSS-REFERENCES 12
4627SERIES99Interchangeable
interchangeable cross-reference
interchangeable
171526Interchangeable
interchangeable cross-reference
interchangeable
4627Interchangeable
interchangeable cross-reference
interchangeable
9151293Interchangeable
interchangeable cross-reference
interchangeable
A7196Interchangeable
interchangeable cross-reference
interchangeable
ARP-115-48Interchangeable
Same NIIN cross-reference
interchangeable
LIFECYCLE
StatusACTIVE
AvailabilityOEM and secondary market
RoHS CompliantEAR99Not HAZMAT
Ready to buy A-7196?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is A-7196?
A-7196 is a RESISTOR,FIXED,WIRE WOUND,INDUCT. It is classified as a MRO (MRO_GENERAL).
What parts can replace A-7196?
There are 12 known substitutes for A-7196: 4627SERIES99, 171526, 4627 and 9 more. Substitute compatibility should be verified for your specific system.
What is the NSN for A-7196?
A-7196 is cataloged in the Federal Logistics Information System (FLIS) under NSN 5330-00-016-6320. This indicates validated use in U.S. government and defense supply chains.
Community Feedback
Comments (0)
No comments yet. Be the first to share what you know.
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — A-7196

✓ Validated with multiple authoritative sources, including Government, OEM, and Certified sources.
PartsTable Design LLC · partstable.com
Last verified: July 2026