9P-20 — SHAFT,STRAIGHT

✓ Government record, cited

— · COMPONENT

PRODUCT OVERVIEW

9P-20: SHAFT,STRAIGHT.

The SHAFT,STRAIGHT is a the manufacturer industrial component. Key specifications include material: STEEL, end_similarity: NOT IDENTICAL, overall_length: 7.125 INCHES NOMINAL IN, surface_finish: 16.0 MICROINCHES, first_end_style: THREADED CROSS DRILLED (THRU HOLE), second_end_style: CIRCULAR GROOVED AND SPLINED (STRAIGHT). This part is cataloged in the U.S.

Government catalog under NSN 3040-01-185-5385, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.

Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS

9P-20

NSN: 3040-01-185-5385
FSC: 3040 — Miscellaneous Power Transmission Equipment
CAGE: 11757 — PARKER HANNIFIN CORPORATION DIV CHELSEA PRODUCTS DIVISION (USA)

SPECIFICATIONS

material	STEEL
end_similarity	NOT IDENTICAL
overall_length	7.125 INCHES NOMINAL IN
surface_finish	16.0 MICROINCHES
first_end_style	THREADED CROSS DRILLED (THRU HOLE)
second_end_style	CIRCULAR GROOVED AND SPLINED (STRAIGHT)
special_features	SECOND END HAS PARIAL BORE WITH UNTHREADED 0.156 INCH DIAMETER LOCATED ON ONE SIDE IN
first_end_diameter	1.2495 INCHES MINIMUM AND 1.2500 INCHES MAXIMUM IN
second_end_diameter	1.2495 INCHES MINIMUM AND 1.2500 INCHES MAXIMUM IN
second_end_groove_width	0.0730 INCHES NOMINAL IN
second_end_spline_length	0.7490 INCHES MINIMUM AND 0.7500 INCHES MAXIMUM IN
second_end_groove_diameter	0.7490 INCHES MINIMUM AND 0.7500 INCHES MAXIMUM IN
NSN	3040-01-185-5385

COMPONENT DIAGRAM

KEY FEATURES

•

SURFACE FINISH: 16.0 MICROINCHES

•

FIRST END DIAMETER: 1.2495 INCHES MINIMUM AND 1.2500 INCHES MAXIMUM IN

•

SECOND END DIAMETER: 1.2495 INCHES MINIMUM AND 1.2500 INCHES MAXIMUM IN

•

SECOND END SPLINE MINOR DIAMETER: 1.0230 INCHES MINIMUM AND 1.0800 INCHES MAXIMUM IN

•

FIRST END STYLE: THREADED CROSS DRILLED (THRU HOLE)

•

SECOND END SPLINE MAJOR DIAMETER: 1.2495 INCHES MINIMUM AND 1.2500 INCHES MAXIMUM IN

•

MATERIAL DOCUMENT AND CLASSIFICATION: QQ-S-624 FED SPEC SINGLE MATERIAL RESPONSE

TECHNICAL CHARACTERISTICS

SURFACE FINISH	16.0 MICROINCHES
FIRST END DIAMETER	1.2495 INCHES MINIMUM AND 1.2500 INCHES MAXIMUM IN
SECOND END DIAMETER	1.2495 INCHES MINIMUM AND 1.2500 INCHES MAXIMUM IN
SECOND END SPLINE MINOR DIAMETER	1.0230 INCHES MINIMUM AND 1.0800 INCHES MAXIMUM IN
FIRST END STYLE	THREADED CROSS DRILLED (THRU HOLE)
SECOND END SPLINE MAJOR DIAMETER	1.2495 INCHES MINIMUM AND 1.2500 INCHES MAXIMUM IN
MATERIAL DOCUMENT AND CLASSIFICATION	QQ-S-624 FED SPEC SINGLE MATERIAL RESPONSE
OVERALL LENGTH	7.125 INCHES NOMINAL IN
SECOND END GROOVE DIAMETER	0.7490 INCHES MINIMUM AND 0.7500 INCHES MAXIMUM IN
END SIMILARITY	NOT IDENTICAL

SUBSTITUTES & CROSS-REFERENCES 1

328-775XSame NSN cross-reference

Same NSN cross-reference

Also cataloged under this NSN

LIFECYCLE

NSN statusActive· U.S. Government catalog

Acquisition advice: Normally procured from the manufacturer (OEM)No demilitarization required

Ready to buy 9P-20?

Compare prices from verified sellers on eBay

Buy on eBay →

As an eBay Partner, PartsTable may earn a commission. Your price is not affected.

FREQUENTLY ASKED QUESTIONS

What is 9P-20?

9P-20 is a SHAFT,STRAIGHT.

What parts can replace 9P-20?

There is 1 known substitute for 9P-20: 328-775X. Substitute compatibility should be verified for your specific system.

What is the NSN for 9P-20?

9P-20 is cataloged in the U.S. Government catalog under NSN 3040-01-185-5385. This indicates validated use in U.S. government and defense supply chains.

Community Feedback

9P-20 — SHAFT,STRAIGHT

Request a Quote — 9P-20