PartsTable
Technical Data Sheet
Download PDF

9-1938 — BEARING,PLAIN,SELF-ALIGNING

✓ Government record, cited
— · ORING SEAL
PRODUCT OVERVIEW

9-1938: BEARING,PLAIN,SELF-ALIGNING.

The BEARING,PLAIN,SELF-ALIGNING is a the manufacturer industrial component. Key specifications include material: RUBBER SEALING ELEMENT, seal_width: 0.610 INCHES MINIMUM AND 0.640 INCHES MAXIMUM IN, construction: SOLID, housing_bore_diameter: 1.573 INCHES MINIMUM AND 1.579 INCHES MAXIMUM IN, accommodated_shaft_diameter: 1.184 INCHES MINIMUM AND 1.186 INCHES MAXIMUM IN, material_document_and_classification: BG720B14,FSCM 81306 MFR REF SINGLE MATERIAL RESPONSE SEALING ELEMENT. This part is cataloged in the U.S.

Government catalog under NSN 5330-00-414-2005, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.

Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
9-1938
NSN: 5330-00-414-2005
NIINs: 004142005, 010122640, 012823292
FSC: 5330 — Packing and Gasket Materials
CAGE: 53800 — SEARS, ROEBUCK AND CO. DBA SEARS DIV SEARS COMMERCIAL (USA)
SPECIFICATIONS
materialRUBBER SEALING ELEMENT
seal_width0.610 INCHES MINIMUM AND 0.640 INCHES MAXIMUM IN
constructionSOLID
housing_bore_diameter1.573 INCHES MINIMUM AND 1.579 INCHES MAXIMUM IN
accommodated_shaft_diameter1.184 INCHES MINIMUM AND 1.186 INCHES MAXIMUM IN
material_document_and_classificationBG720B14,FSCM 81306 MFR REF SINGLE MATERIAL RESPONSE SEALING ELEMENT
NSN5330-00-414-2005
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: 9-1938 MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
CROSS-SECTIONAL HEIGHT: 0.640 INCHES MINIMUM AND 0.670 INCHES MAXIMUM IN
•
PERIPHERAL DIAMETER: 1.569 INCHES MINIMUM AND 1.575 INCHES MAXIMUM IN
•
CENTER HOLE DIAMETER: 1.184 INCHES MINIMUM AND 1.186 INCHES MAXIMUM IN
TECHNICAL CHARACTERISTICS
CROSS-SECTIONAL HEIGHT0.640 INCHES MINIMUM AND 0.670 INCHES MAXIMUM IN
PERIPHERAL DIAMETER1.569 INCHES MINIMUM AND 1.575 INCHES MAXIMUM IN
CENTER HOLE DIAMETER1.184 INCHES MINIMUM AND 1.186 INCHES MAXIMUM IN
SUBSTITUTES & CROSS-REFERENCES 1
99404Reference document
Same NSN cross-reference
Reference document — Secondary reference
LIFECYCLE
NSN statusCancelled· U.S. Government catalog
Acquisition advice: Normally procured from the manufacturer (OEM)No demilitarization required
Ready to buy 9-1938?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is 9-1938?
9-1938 is a BEARING,PLAIN,SELF-ALIGNING.
What parts can replace 9-1938?
There is 1 known substitute for 9-1938: 99404. Substitute compatibility should be verified for your specific system.
What is the NSN for 9-1938?
9-1938 is cataloged in the U.S. Government catalog under NSN 5330-00-414-2005. This indicates validated use in U.S. government and defense supply chains.
Community Feedback
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — 9-1938