PartsTable
Technical Data Sheet
PartsTable / COMPONENT / 702-132-031-007
702-132-031-007 ✓ Verified by PartsTable
— · ORING SEAL
WHAT YOU NEED TO KNOW
Material determines chemical compatibility Standard durometer is 70 Shore A
Wrong material = catastrophic seal failure
PRODUCT OVERVIEW

The CLAMP,LOOP is a the manufacturer industrial component. Key specifications include diameter: 0.137 INCHES MINIMUM AND 0.174 INCHES MAXIMUM IN, material: PLASTIC POLYAMIDE NYLON BAND, overall_width: 0.350 INCHES MINIMUM AND 0.410 INCHES MAXIMUM IN, style_designator: SINGLE LOOP, tongue_hole_type: ROUND, UNTHREADED, material_thickness: 0.035 INCHES MINIMUM AND 0.045 INCHES MAXIMUM IN. This product is currently in active production with full OEM support.

This part is cataloged in the Federal Logistics Information System (FLIS) under NSN 5340-00-168-6708, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.

Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
702-132-031-007
NSN: 5340-00-168-6708
FSC: 5340
CAGE: 90073 — CMC ELECTRONICS INC (CAN)
SPECIFICATIONS
diameter0.137 INCHES MINIMUM AND 0.174 INCHES MAXIMUM IN
materialPLASTIC POLYAMIDE NYLON BAND
overall_width0.350 INCHES MINIMUM AND 0.410 INCHES MAXIMUM IN
style_designatorSINGLE LOOP
tongue_hole_typeROUND, UNTHREADED
material_thickness0.035 INCHES MINIMUM AND 0.045 INCHES MAXIMUM IN
loop_inside_diameter0.330 INCHES MINIMUM AND 0.390 INCHES MAXIMUM IN
material_document_and_classificationL-P-410 FED SPEC SINGLE MATERIAL RESPONSE BAND
distance_from_loop_center_to_tongue_end0.650 INCHES NOMINAL IN
center_to_center_distance_between_loop_and_mounting_hole0.420 INCHES MINIMUM AND 0.540 INCHES MAXIMUM IN
NSN5340-00-168-6708
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: 702-132-031-007 MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
CENTER TO CENTER DISTANCE BETWEEN LOOP AND MOUNTING HOLE: 0.420 INCHES MINIMUM AND 0.540 INCHES MAXIMUM IN
•
STYLE DESIGNATOR: SINGLE LOOP
•
MATERIAL DOCUMENT AND CLASSIFICATION: L-P-410 FED SPEC SINGLE MATERIAL RESPONSE BAND
•
LOOP INSIDE DIAMETER: 0.330 INCHES MINIMUM AND 0.390 INCHES MAXIMUM IN
•
DISTANCE FROM LOOP CENTER TO TONGUE END: 0.650 INCHES NOMINAL IN
•
TONGUE HOLE TYPE: ROUND, UNTHREADED
TECHNICAL CHARACTERISTICS (FLIS)
CENTER TO CENTER DISTANCE BETWEEN LOOP AND MOUNTING HOLE0.420 INCHES MINIMUM AND 0.540 INCHES MAXIMUM IN
STYLE DESIGNATORSINGLE LOOP
MATERIAL DOCUMENT AND CLASSIFICATIONL-P-410 FED SPEC SINGLE MATERIAL RESPONSE BAND
STYLE DESIGNATORSINGLE LOOP
LOOP INSIDE DIAMETER0.330 INCHES MINIMUM AND 0.390 INCHES MAXIMUM IN
MATERIAL DOCUMENT AND CLASSIFICATIONL-P-410 FED SPEC SINGLE MATERIAL RESPONSE BAND
DISTANCE FROM LOOP CENTER TO TONGUE END0.650 INCHES NOMINAL IN
TONGUE HOLE TYPEROUND, UNTHREADED
MATERIALPLASTIC POLYAMIDE NYLON BAND
CENTER TO CENTER DISTANCE BETWEEN LOOP AND MOUNTING HOLE0.420 INCHES MINIMUM AND 0.540 INCHES MAXIMUM IN
VERIFIED SUBSTITUTES & CROSS-REFERENCES 6
55-22281-54AInterchangeable
interchangeable cross-reference
interchangeable
X4Interchangeable
interchangeable cross-reference
interchangeable
G1-1010-18Interchangeable
interchangeable cross-reference
interchangeable
X277 (18373-8)Interchangeable
interchangeable cross-reference
interchangeable
18372Interchangeable
interchangeable cross-reference
interchangeable
132-031GInterchangeable
Same NIIN cross-reference
interchangeable
LIFECYCLE
StatusACTIVE
AvailabilityOEM and secondary market
RoHS CompliantEAR99Not HAZMAT
Ready to buy 702-132-031-007?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is 702-132-031-007?
702-132-031-007 is a CLAMP,LOOP.
What parts can replace 702-132-031-007?
There are 6 known substitutes for 702-132-031-007: 55-22281-54A, X4, G1-1010-18 and 3 more. Substitute compatibility should be verified for your specific system.
What is the NSN for 702-132-031-007?
702-132-031-007 is cataloged in the Federal Logistics Information System (FLIS) under NSN 5340-00-168-6708. This indicates validated use in U.S. government and defense supply chains.
Community Feedback
Comments (0)
No comments yet. Be the first to share what you know.
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — 702-132-031-007

✓ Validated with multiple authoritative sources, including Government, OEM, and Certified sources.
PartsTable Design LLC · partstable.com
Last verified: July 2026