PartsTable
Technical Data Sheet
Download PDF

6490-12 — SCREW,TAPPING

✓ Government record, cited
— · ORING SEAL
PRODUCT OVERVIEW

6490-12: SCREW,TAPPING.

The SCREW,TAPPING is a the manufacturer industrial component. Key specifications include head_style: FILLISTER, head_height: 0.133 INCHES MINIMUM AND 0.156 INCHES MAXIMUM IN, head_diameter: 0.250 INCHES MINIMUM AND 0.270 INCHES MAXIMUM IN, fastener_length: 0.750 INCHES NOMINAL IN, special_features: BLACK CHROMATE WITH VINYL WAS COATING FINISH, surface_treatment: CHROMATE OVERALL. This part is cataloged in the U.S.

Government catalog under NSN 5330-00-924-9040, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.

Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
6490-12
NSN: 5330-00-924-9040
NIINs: 009249040, 015136016
FSC: 5330 — Packing and Gasket Materials
CAGE: 83259 — PARKER-HANNIFIN CORPORATION DBA PNEUTRONICS DIV COMPOSITE SEALING SYSTEMS DIVISION (USA)
SPECIFICATIONS
head_styleFILLISTER
head_height0.133 INCHES MINIMUM AND 0.156 INCHES MAXIMUM IN
head_diameter0.250 INCHES MINIMUM AND 0.270 INCHES MAXIMUM IN
fastener_length0.750 INCHES NOMINAL IN
special_featuresBLACK CHROMATE WITH VINYL WAS COATING FINISH
surface_treatmentCHROMATE OVERALL
internal_drive_styleSIX SPLINE
nonmachine_nominal_thread_diameter0.164 INCHES IN
part_name_assigned_by_controlling_agencyNO. 8-32 SCREWS TAPTITE TORX FILLISTER HEAD
NSN5330-00-924-9040
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: 6490-12 MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
TEMP RATING: -65.0 FAHRENHEIT AND 308.0 FAHRENHEIT DEGF
•
SURFACE TREATMENT DOCUMENT AND CLASSIFICATION: MIL-A-8625 MIL SPEC SINGLE TREATMENT RESPONSE OVERALL
•
CROSS-SECTIONAL THICKNESS: 0.150 INCHES NOMINAL IN
•
CROSS-SECTIONAL SHAPE STYLE: METAL AND SYNTHETIC RUBBER
•
SURFACE TREATMENT: ANODIZE OVERALL
•
MATERIAL: ALUMINUM ALLOY OVERALL
TECHNICAL CHARACTERISTICS
TEMP RATING-65.0 FAHRENHEIT AND 308.0 FAHRENHEIT DEGF
SURFACE TREATMENT DOCUMENT AND CLASSIFICATIONMIL-A-8625 MIL SPEC SINGLE TREATMENT RESPONSE OVERALL
CROSS-SECTIONAL THICKNESS0.150 INCHES NOMINAL IN
CROSS-SECTIONAL SHAPE STYLEMETAL AND SYNTHETIC RUBBER
SURFACE TREATMENTANODIZE OVERALL
MATERIALALUMINUM ALLOY OVERALL
SUBSTITUTES & CROSS-REFERENCES 2
2032-1Same NSN cross-reference
Same NSN cross-reference
Also cataloged under this NSN
2032Reference document
Same NSN cross-reference
Reference document — Secondary reference
LIFECYCLE
NSN statusActive· U.S. Government catalog
Acquisition advice: Normally procured from the manufacturer (OEM)No demilitarization required
Ready to buy 6490-12?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is 6490-12?
6490-12 is a SCREW,TAPPING.
What parts can replace 6490-12?
There are 2 known substitutes for 6490-12: 2032-1, 2032. Substitute compatibility should be verified for your specific system.
What is the NSN for 6490-12?
6490-12 is cataloged in the U.S. Government catalog under NSN 5330-00-924-9040. This indicates validated use in U.S. government and defense supply chains.
Community Feedback
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — 6490-12