PartsTable
Technical Data Sheet
Download PDF

6009-15CC — CLIP,SPRING TENSION

✓ Government record, cited
— · ORING SEAL
PRODUCT OVERVIEW

6009-15CC: CLIP,SPRING TENSION.

The CLIP,SPRING TENSION is a the manufacturer industrial component. Key specifications include width: 0.365 INCHES MINIMUM AND 0.385 INCHES MAXIMUM IN, length: 0.323 INCHES MINIMUM AND 0.343 INCHES MAXIMUM IN, material: COPPER ALLOY 172 OVERALL, hole_diameter: 0.092 INCHES MINIMUM AND 0.096 INCHES MAXIMUM IN, overall_height: 0.367 INCHES MINIMUM AND 0.387 INCHES MAXIMUM IN, surface_treatment: CADMIUM AND CHROMATE OVERALL. This part is cataloged in the U.S.

Government catalog under NSN 5340-00-870-4031, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.

Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
6009-15CC
NSN: 5340-00-870-4031
FSC: 5340 — Hardware, Commercial
CAGE: 00779 — TE CONNECTIVITY CORPORATION (USA)
SPECIFICATIONS
width0.365 INCHES MINIMUM AND 0.385 INCHES MAXIMUM IN
length0.323 INCHES MINIMUM AND 0.343 INCHES MAXIMUM IN
materialCOPPER ALLOY 172 OVERALL
hole_diameter0.092 INCHES MINIMUM AND 0.096 INCHES MAXIMUM IN
overall_height0.367 INCHES MINIMUM AND 0.387 INCHES MAXIMUM IN
surface_treatmentCADMIUM AND CHROMATE OVERALL
material_thickness0.009 INCHES MINIMUM AND 0.012 INCHES MAXIMUM IN
loop/holding_dimension0.307 INCHES MINIMUM AND 0.322 INCHES MAXIMUM IN
distance_from_loop_center_to_end0.218 INCHES NOMINAL IN
material_document_and_classificationQQ-C-533,ALLOY 172 FED SPEC SINGLE MATERIAL RESPONSE OVERALL
surface_treatment_document_and_classificationQQ-P-416,TYPE 2,CLASS 2 FED SPEC SINGLE TREATMENT RESPONSE OVERALL
NSN5340-00-870-4031
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: 6009-15CC MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
LENGTH: 0.323 INCHES MINIMUM AND 0.343 INCHES MAXIMUM IN
•
SURFACE TREATMENT DOCUMENT AND CLASSIFICATION: QQ-P-416,TYPE 2,CLASS 2 FED SPEC SINGLE TREATMENT RESPONSE OVERALL
•
MATERIAL DOCUMENT AND CLASSIFICATION: QQ-C-533,ALLOY 172 FED SPEC SINGLE MATERIAL RESPONSE OVERALL
•
LOOP/HOLDING DIMENSION: 0.307 INCHES MINIMUM AND 0.322 INCHES MAXIMUM IN
•
MATERIAL THICKNESS: 0.009 INCHES MINIMUM AND 0.012 INCHES MAXIMUM IN
•
DISTANCE FROM LOOP CENTER TO END: 0.218 INCHES NOMINAL IN
•
SURFACE TREATMENT: CADMIUM AND CHROMATE OVERALL
TECHNICAL CHARACTERISTICS
OVERALL HEIGHT0.367 INCHES MINIMUM AND 0.387 INCHES MAXIMUM IN
LENGTH0.323 INCHES MINIMUM AND 0.343 INCHES MAXIMUM IN
SURFACE TREATMENT DOCUMENT AND CLASSIFICATIONQQ-P-416,TYPE 2,CLASS 2 FED SPEC SINGLE TREATMENT RESPONSE OVERALL
MATERIAL DOCUMENT AND CLASSIFICATIONQQ-C-533,ALLOY 172 FED SPEC SINGLE MATERIAL RESPONSE OVERALL
LOOP/HOLDING DIMENSION0.307 INCHES MINIMUM AND 0.322 INCHES MAXIMUM IN
MATERIAL THICKNESS0.009 INCHES MINIMUM AND 0.012 INCHES MAXIMUM IN
DISTANCE FROM LOOP CENTER TO END0.218 INCHES NOMINAL IN
SURFACE TREATMENTCADMIUM AND CHROMATE OVERALL
WIDTH0.365 INCHES MINIMUM AND 0.385 INCHES MAXIMUM IN
MATERIALCOPPER ALLOY 172 OVERALL
SUBSTITUTES & CROSS-REFERENCES 1
110-001-0007Reference document
Same NSN cross-reference
Reference document — Vendor item drawing reference
LIFECYCLE
NSN statusActive· U.S. Government catalog
Acquisition advice: Semi-active item — no replacement plannedNo demilitarization required
Ready to buy 6009-15CC?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is 6009-15CC?
6009-15CC is a CLIP,SPRING TENSION.
What parts can replace 6009-15CC?
There is 1 known substitute for 6009-15CC: 110-001-0007. Substitute compatibility should be verified for your specific system.
What is the NSN for 6009-15CC?
6009-15CC is cataloged in the U.S. Government catalog under NSN 5340-00-870-4031. This indicates validated use in U.S. government and defense supply chains.
Community Feedback
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — 6009-15CC

✓ PartsTable — the parts reference. Every fact cited to its source.
PartsTable Design LLC · partstable.com
U.S. Government catalog: edition PUBLOGDVD v12.0.0 (OCT 2026), edition date 2026-10-01, retrieved 2026-10-18.
PartsTable commercial catalog: edition Unified commercial catalog snapshot through 2026-09-28, edition date not on file, retrieved 2026-09-28.