PartsTable
Technical Data Sheet
PartsTable / COMPONENT / 5330009390666
5330009390666 ✓ Verified by PartsTable
— · ORING SEAL
WHAT YOU NEED TO KNOW
Material determines chemical compatibility Standard durometer is 70 Shore A
Wrong material = catastrophic seal failure
PRODUCT OVERVIEW

The GASKET is a the manufacturer industrial component. Key specifications include material: RUBBER CHLOROPRENE CLASS CR OVERALL, hole_diameter: 0.162 INCHES MINIMUM AND 0.182 INCHES MAXIMUM LOCATION NOT OTHERWISE SPECIFIED IN, overall_width: 1.094 INCHES MINIMUM AND 1.110 INCHES MAXIMUM IN, overall_length: 1.094 INCHES MINIMUM AND 1.110 INCHES MAXIMUM IN, hardness_rating: 75.0 SHORE DUROMETER A MINIMUM AND 85.0 SHORE DUROMETER A MAXIMUM OVERALL, style_designator: NON-CIRCULAR. This part is cataloged in the Federal Logistics Information System (FLIS) under NSN 5330-00-939-0666, indicating validated use in U.S.

government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels. Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
5330009390666
NSN: 5330-00-939-0666
FSC: 5330
CAGE: SCY13 — E.C.A ETABLISSEMENT CENTRALD'APPROVISIONNEMENT DES FORCES ARMEE
SPECIFICATIONS
materialRUBBER CHLOROPRENE CLASS CR OVERALL
hole_diameter0.162 INCHES MINIMUM AND 0.182 INCHES MAXIMUM LOCATION NOT OTHERWISE SPECIFIED IN
overall_width1.094 INCHES MINIMUM AND 1.110 INCHES MAXIMUM IN
overall_length1.094 INCHES MINIMUM AND 1.110 INCHES MAXIMUM IN
hardness_rating75.0 SHORE DUROMETER A MINIMUM AND 85.0 SHORE DUROMETER A MAXIMUM OVERALL
style_designatorNON-CIRCULAR
aperture_diameter0.750 INCHES MINIMUM AND 0.766 INCHES MAXIMUM IN
bolt_hole_quantity4
outside_corner_radius0.131 INCHES MINIMUM AND 0.151 INCHES MAXIMUM IN
cross-sectional_thickness0.026 INCHES MINIMUM AND 0.036 INCHES MAXIMUM IN
cross-sectional_shape_styleSOLID SINGLE OR COMPOSITION
material_document_and_classificationASTM D2000 2BC815C1E3 ASSN STD SINGLE MATERIAL RESPONSE OVERALL
NSN5330-00-939-0666
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: 5330009390666 MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
APERTURE DIAMETER: 0.750 INCHES MINIMUM AND 0.766 INCHES MAXIMUM IN
•
OUTSIDE EDGE TO BOLT HOLE CENTER DISTANCE ALONG LENGTH: 0.131 INCHES MINIMUM AND 0.151 INCHES MAXIMUM IN
•
CROSS-SECTIONAL THICKNESS: 0.026 INCHES MINIMUM AND 0.036 INCHES MAXIMUM IN
•
BOLT HOLE QUANTITY: 4
•
CENTER TO CENTER DISTANCE BETWEEN BOLT HOLES ALONG LENGTH: 0.803 INCHES MINIMUM AND 0.823 INCHES MAXIMUM LOCATION NOT OTHERWISE SPECIFIED IN
•
HOLE DIAMETER: 0.162 INCHES MINIMUM AND 0.182 INCHES MAXIMUM LOCATION NOT OTHERWISE SPECIFIED IN
TECHNICAL CHARACTERISTICS (FLIS)
OVERALL LENGTH1.094 INCHES MINIMUM AND 1.110 INCHES MAXIMUM IN
APERTURE DIAMETER0.750 INCHES MINIMUM AND 0.766 INCHES MAXIMUM IN
OUTSIDE EDGE TO BOLT HOLE CENTER DISTANCE ALONG LENGTH0.131 INCHES MINIMUM AND 0.151 INCHES MAXIMUM IN
CROSS-SECTIONAL THICKNESS0.026 INCHES MINIMUM AND 0.036 INCHES MAXIMUM IN
BOLT HOLE QUANTITY4
CENTER TO CENTER DISTANCE BETWEEN BOLT HOLES ALONG LENGTH0.803 INCHES MINIMUM AND 0.823 INCHES MAXIMUM LOCATION NOT OTHERWISE SPECIFIED IN
HOLE DIAMETER0.162 INCHES MINIMUM AND 0.182 INCHES MAXIMUM LOCATION NOT OTHERWISE SPECIFIED IN
OVERALL WIDTH1.094 INCHES MINIMUM AND 1.110 INCHES MAXIMUM IN
MATERIAL DOCUMENT AND CLASSIFICATIONASTM D2000 2BC815C1E3 ASSN STD SINGLE MATERIAL RESPONSE OVERALL
CENTER TO CENTER DISTANCE BETWEEN BOLT HOLES ALONG WIDTH0.803 INCHES MINIMUM AND 0.823 INCHES MAXIMUM LOCATION NOT OTHERWISE SPECIFIED IN
VERIFIED SUBSTITUTES & CROSS-REFERENCES 32
MAGNA-TAC M648T/CH-8Interchangeable
interchangeable cross-reference
interchangeable
M648T/CH-8Interchangeable
interchangeable cross-reference
interchangeable
5330002387383Interchangeable
interchangeable cross-reference
interchangeable
MS52000-1Interchangeable
interchangeable cross-reference
interchangeable
MS52000-6Interchangeable
interchangeable cross-reference
interchangeable
7358504Interchangeable
interchangeable cross-reference
interchangeable
LIFECYCLE
StatusCANCELLED
Availability—
RoHS CompliantEAR99Not HAZMAT
Ready to buy 5330009390666?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is 5330009390666?
5330009390666 is a GASKET.
What parts can replace 5330009390666?
There are 32 known substitutes for 5330009390666: MAGNA-TAC M648T/CH-8, M648T/CH-8, 5330002387383 and 29 more. Substitute compatibility should be verified for your specific system.
Is 5330009390666 still available?
5330009390666 is currently cancelled.
Community Feedback
Comments (0)
No comments yet. Be the first to share what you know.
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — 5330009390666

✓ Validated with multiple authoritative sources, including Government, OEM, and Certified sources.
PartsTable Design LLC · partstable.com
Last verified: July 2026