PartsTable
Technical Data Sheet
4771-8 ✓ Verified by PartsTable
Lindy · ORING SEAL
WHAT YOU NEED TO KNOW
Material determines chemical compatibility Standard durometer is 70 Shore A
Wrong material = catastrophic seal failure
PRODUCT OVERVIEW

Cat.6 S/FTP network cable with support for bandwidth up to 250MHz and features a snagless design with gold plated contacts for ethernet standards up to 1GBase-T.<br>Cat.6 cable for operating frequencies up to 250MHz in shielded version with braid as overall shield and foil shield for the individual wire pairs (S/FTP). Cat.6 cables are widespread throughout the professional sector. They are ideal for Gigabit Ethernet or AV extension applications.

These cables are manufactured and tested according to the ISO/IEC 11801 specification. The cables are packaged individually in a polybag.<br>The gold-plated contacts ensure reliable, corrosion-free connections over extensive periods of time. A robust snagless strain relief design prevents damage to the connector latch during installation and removal.<br>Available lengths: 0.3m, 0.5m, 1m, 1.5m, 2m, 3m, 5m, 7.5m, 10m, 15m, 20m, 30m.<br>Available colours: Blue, Red, Green, Yellow, Black, White, Orange, Purple, Grey.

This part is cataloged in the Federal Logistics Information System (FLIS) under NSN 5340-00-144-8279, indicating validated use in U.S. government and defense logistics supply chains.

WHERE IT FITS
4771-8
NSN: 5340-00-144-8279
FSC: 5340
CAGE: 83930 — TRANSDIGM INC DBA ADEL WIGGINS GROUP DIV ADEL WIGGINS (USA)
SPECIFICATIONS
diameter0.201 INCHES MINIMUM AND 0.209 INCHES MAXIMUM IN
materialCARBIDE OVERALL
point_typeCONVENTIONAL
base_height1.000 INCHES NOMINAL IN
point_angle118.0 DEGREES NOMINAL
shank_styleSTRAIGHT ROUND
flute_length3.000 INCHES NOMINAL IN
top_diameter1.875 INCHES NOMINAL IN
overall_width0.500 INCHES NOMINAL IN
thread_length0.375 INCHES NOMINAL IN
flute_quantity2
overall_height10.000 INCHES NOMINAL IN
NSN5340-00-144-8279
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: 4771-8 MFR: Lindy ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
MATERIAL THICKNESS: 0.047 INCHES MINIMUM AND 0.053 INCHES MAXIMUM IN
CENTER TO CENTER DISTANCE BETWEEN LOOP AND MOUNTING HOLE: 0.959 INCHES NOMINAL IN
DISTANCE FROM LOOP CENTER TO TONGUE END: 1.177 INCHES NOMINAL IN
DIAMETER: 0.201 INCHES MINIMUM AND 0.209 INCHES MAXIMUM IN
SURFACE TREATMENT: ANODIZE BAND
MATERIAL: PLASTIC TETRAFLUOROETHYLENE CUSHION
TECHNICAL CHARACTERISTICS (FLIS)
MATERIAL THICKNESS0.047 INCHES MINIMUM AND 0.053 INCHES MAXIMUM IN
CENTER TO CENTER DISTANCE BETWEEN LOOP AND MOUNTING HOLE0.959 INCHES NOMINAL IN
DISTANCE FROM LOOP CENTER TO TONGUE END1.177 INCHES NOMINAL IN
OVERALL WIDTH0.500 INCHES NOMINAL IN
DIAMETER0.201 INCHES MINIMUM AND 0.209 INCHES MAXIMUM IN
SURFACE TREATMENTANODIZE BAND
MATERIALPLASTIC TETRAFLUOROETHYLENE CUSHION
MATERIALALUMINUM ALLOY 2024 BAND
LOOP INSIDE DIAMETER1.110 INCHES MINIMUM AND 1.140 INCHES MAXIMUM IN
MATERIAL DOCUMENT AND CLASSIFICATIONQQ-A-250/5,T4 FED SPEC SINGLE MATERIAL RESPONSE BAND
VERIFIED SUBSTITUTES & CROSS-REFERENCES 9
4771-8Interchangeable
interchangeable cross-reference
interchangeable
003623Interchangeable
interchangeable cross-reference
interchangeable
D1E 1/2Interchangeable
interchangeable cross-reference
interchangeable
B94.11MInterchangeable
interchangeable cross-reference
interchangeable
PA47718Interchangeable
interchangeable cross-reference
interchangeable
45616PL FIND NO 39Interchangeable
interchangeable cross-reference
interchangeable
LIFECYCLE
StatusCANCELLED
Availability
RoHS CompliantEAR99Not HAZMAT
Ready to buy 4771-8?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is 4771-8?
4771-8 is a SEMICONDUCTOR DEVICE,THYRISTOR manufactured by Lindy.
What parts can replace 4771-8?
There are 9 known substitutes for 4771-8: 4771-8, 003623, D1E 1/2 and 6 more. Substitute compatibility should be verified for your specific system.
Is 4771-8 still available?
4771-8 is currently cancelled.
Community Feedback
Comments (0)
No comments yet. Be the first to share what you know.
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — 4771-8