PartsTable
Technical Data Sheet
PartsTable / MRO / 4414-1
4414-1 ✓ Verified by PartsTable
Sandberg · MRO · MRO_GENERAL
WHAT YOU NEED TO KNOW
Material determines chemical compatibility Standard durometer is 70 Shore A
Wrong material = catastrophic seal failure
PRODUCT OVERVIEW

Sandberg Survivor Cable is a charging cable that lasts! The cable is made of super-strong Kevlar in double braided nylon, while the connectors are made of cast metal. The extra strong connections ensure that the plug does not break from the cable. Tested to pull over 70kg and bend over 60,000 times.

This part is cataloged in the Federal Logistics Information System (FLIS) under NSN 5330-00-039-6908, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.

Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
MRO→ MRO_GENERAL→ 4414-1
NSN: 5330-00-039-6908
FSC: 5330
CAGE: 64104 — DRESSER, LLC (USA)
SPECIFICATIONS
colorWHITE
width36.000 INCHES NOMINAL IN
length60.000 INCHES NOMINAL IN
materialPLASTIC POLYETHYLENE TEREPHTHALATE (PET)(POLYESTER)
thickness0.004 INCHES IN
point_typeCONVENTIONAL
point_angle118.0 DEGREES NOMINAL
shank_styleSTRAIGHT ROUND
flute_length0.375 INCHES NOMINAL IN
hole_diameter0.406 INCHES NOMINAL LOCATION NOT OTHERWISE SPECIFIED IN
overall_width4.312 INCHES NOMINAL IN
physical_formROLL
NSN5330-00-039-6908
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: 4414-1 MFR: Sandberg ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
OUTSIDE CORNER RADIUS: 0.406 INCHES NOMINAL IN
•
BOLT HOLE QUANTITY: 3
•
SIDE RADIUS FROM GASKET CENTER: 1.500 INCHES NOMINAL IN
•
HOLE DIAMETER: 0.406 INCHES NOMINAL LOCATION NOT OTHERWISE SPECIFIED IN
•
BOLT CIRCLE DIAMETER: 3.500 INCHES NOMINAL IN
•
APERTURE DIAMETER: 2.438 INCHES NOMINAL IN
•
STYLE DESIGNATOR: NON-CIRCULAR
TECHNICAL CHARACTERISTICS (FLIS)
OVERALL WIDTH4.312 INCHES NOMINAL IN
OUTSIDE CORNER RADIUS0.406 INCHES NOMINAL IN
BOLT HOLE QUANTITY3
SIDE RADIUS FROM GASKET CENTER1.500 INCHES NOMINAL IN
HOLE DIAMETER0.406 INCHES NOMINAL LOCATION NOT OTHERWISE SPECIFIED IN
BOLT CIRCLE DIAMETER3.500 INCHES NOMINAL IN
APERTURE DIAMETER2.438 INCHES NOMINAL IN
STYLE DESIGNATORNON-CIRCULAR
MATERIALPAPER OVERALL
CROSS-SECTIONAL THICKNESS0.031 INCHES NOMINAL IN
VERIFIED SUBSTITUTES & CROSS-REFERENCES 8
C01032Interchangeable
interchangeable cross-reference
interchangeable
150 71Interchangeable
interchangeable cross-reference
interchangeable
R18Interchangeable
interchangeable cross-reference
interchangeable
44-141Interchangeable
interchangeable cross-reference
interchangeable
4414-3Interchangeable
interchangeable cross-reference
interchangeable
N764829Interchangeable
interchangeable cross-reference
interchangeable
LIFECYCLE
StatusACTIVE
AvailabilityOEM and secondary market
RoHS CompliantEAR99Not HAZMAT
Ready to buy 4414-1?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is 4414-1?
4414-1 is a RESISTOR,VARIABLE,WIRE WOUND,PRE manufactured by Sandberg. It is classified as a MRO (MRO_GENERAL).
What parts can replace 4414-1?
There are 8 known substitutes for 4414-1: C01032, 150 71, R18 and 5 more. Substitute compatibility should be verified for your specific system.
What is the NSN for 4414-1?
4414-1 is cataloged in the Federal Logistics Information System (FLIS) under NSN 5330-00-039-6908. This indicates validated use in U.S. government and defense supply chains.
Community Feedback
Comments (0)
No comments yet. Be the first to share what you know.
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — 4414-1

✓ Validated with multiple authoritative sources, including Government, OEM, and Certified sources.
PartsTable Design LLC · partstable.com
Last verified: July 2026