PartsTable
Technical Data Sheet
PartsTable / COMPONENT / 43E00300-13
43E00300-13 ✓ Verified by PartsTable
— · ORING SEAL
WHAT YOU NEED TO KNOW
Material determines chemical compatibility Standard durometer is 70 Shore A
Wrong material = catastrophic seal failure
PRODUCT OVERVIEW

The CLIP,SPRING TENSION is a the manufacturer industrial component. Key specifications include length: 0.562 INCHES NOMINAL IN, material: STEEL CORROSION RESISTING OVERALL, hole_diameter: 0.125 INCHES NOMINAL IN, overall_height: 0.750 INCHES NOMINAL IN, surface_treatment: PLASTIC OVERALL, loop/holding_dimension: 0.312 INCHES MINIMUM AND 0.562 INCHES MAXIMUM IN. This product is currently in active production with full OEM support.

This part is cataloged in the Federal Logistics Information System (FLIS) under NSN 5340-01-005-3120, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.

Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
43E00300-13
NSN: 5340-01-005-3120
FSC: 5340
CAGE: 80020 — NAVAL AIR WARFARE CENTER AIRCRAFT DIVISION JOINT BASE JBMDL (USA)
SPECIFICATIONS
length0.562 INCHES NOMINAL IN
materialSTEEL CORROSION RESISTING OVERALL
hole_diameter0.125 INCHES NOMINAL IN
overall_height0.750 INCHES NOMINAL IN
surface_treatmentPLASTIC OVERALL
loop/holding_dimension0.312 INCHES MINIMUM AND 0.562 INCHES MAXIMUM IN
NSN5340-01-005-3120
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: 43E00300-13 MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
SURFACE TREATMENT: PLASTIC OVERALL
•
MATERIAL: STEEL CORROSION RESISTING OVERALL
•
HOLE DIAMETER: 0.125 INCHES NOMINAL IN
•
LENGTH: 0.562 INCHES NOMINAL IN
•
LOOP/HOLDING DIMENSION: 0.312 INCHES MINIMUM AND 0.562 INCHES MAXIMUM IN
TECHNICAL CHARACTERISTICS (FLIS)
OVERALL HEIGHT0.750 INCHES NOMINAL IN
SURFACE TREATMENTPLASTIC OVERALL
MATERIALSTEEL CORROSION RESISTING OVERALL
HOLE DIAMETER0.125 INCHES NOMINAL IN
LENGTH0.562 INCHES NOMINAL IN
LOOP/HOLDING DIMENSION0.312 INCHES MINIMUM AND 0.562 INCHES MAXIMUM IN
VERIFIED SUBSTITUTES & CROSS-REFERENCES 3
4SE00300-13Interchangeable
interchangeable cross-reference
interchangeable
ER104166G1Interchangeable
interchangeable cross-reference
interchangeable
ER104166-001Interchangeable
interchangeable cross-reference
interchangeable
LIFECYCLE
StatusACTIVE
AvailabilityOEM and secondary market
RoHS CompliantEAR99Not HAZMAT
Ready to buy 43E00300-13?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is 43E00300-13?
43E00300-13 is a CLIP,SPRING TENSION.
What parts can replace 43E00300-13?
There are 3 known substitutes for 43E00300-13: 4SE00300-13, ER104166G1, ER104166-001. Substitute compatibility should be verified for your specific system.
What is the NSN for 43E00300-13?
43E00300-13 is cataloged in the Federal Logistics Information System (FLIS) under NSN 5340-01-005-3120. This indicates validated use in U.S. government and defense supply chains.
Community Feedback
Comments (0)
No comments yet. Be the first to share what you know.
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — 43E00300-13

✓ Validated with multiple authoritative sources, including Government, OEM, and Certified sources.
PartsTable Design LLC · partstable.com
Last verified: July 2026