PartsTable
Technical Data Sheet
Download PDF

385AX384DRBX2S385A — BEARING,ROLLER,TAPERED

✓ Government record, cited
— · TAPERED BEARING
PRODUCT OVERVIEW

385AX384DRBX2S385A: BEARING,ROLLER,TAPERED.

The BEARING,ROLLER,TAPERED is a the manufacturer tape media or drive component used in enterprise backup, archival, and disaster recovery environments. Key specifications include material: STEEL OVERALL, cup_width: 1.5620 INCHES NOMINAL IN, cone_width: 1.9370 INCHES NOMINAL IN, bore_diameter: 2.0000 INCHES NOMINAL IN, overall_width: 1.9370 INCHES NOMINAL IN, standout_width: 0.1875 INCHES NOMINAL IN. This part is cataloged in the U.S.

Government catalog under NSN 3110-00-119-8172, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.

Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
385AX384DRBX2S385A
NSN: 3110-00-119-8172
FSC: 3110 — Bearings, Antifriction, Unmounted
CAGE: 60038 — THE TIMKEN CORPORATION (USA)
SPECIFICATIONS
materialSTEEL OVERALL
cup_width1.5620 INCHES NOMINAL IN
cone_width1.9370 INCHES NOMINAL IN
bore_diameter2.0000 INCHES NOMINAL IN
overall_width1.9370 INCHES NOMINAL IN
standout_width0.1875 INCHES NOMINAL IN
special_featuresBENCH LATERAL 0.0080 IN,SNAP RING GROOVE IN OD,HOLE IN OD FOR LOCKING PIN IN
cone_corner_radius0.0300 INCHES NOMINAL IN
backface_corner_radius0.0300 INCHES NOMINAL IN
overall_outside_diameter4.1250 INCHES NOMINAL IN
NSN3110-00-119-8172
COMPONENT DIAGRAM
TAPERED ROLLER BEARING — CUP & CONE ASSEMBLY CAGE CUP BORE CONE OD: — · BORE: — · WIDTH: — Single Row · PN: 385AX384DRBX2S385A · OEM ⚠ VERIFY BEFORE ORDERING Cup and cone sold separately — verify you are ordering BOTH parts or the correct component. Always replace cup and cone together — mismatched wear = premature failure ✓ BROKER TIP Taper angle determines axial load capacity. Steeper angle = higher axial load rating. Timken series numbers indicate dimensions — cross-reference carefully PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
CUP WIDTH: 1.5620 INCHES NOMINAL IN
•
OVERALL OUTSIDE DIAMETER: 4.1250 INCHES NOMINAL IN
•
BACKFACE CORNER RADIUS: 0.0300 INCHES NOMINAL IN
•
CONE CORNER RADIUS: 0.0300 INCHES NOMINAL IN
•
STANDOUT WIDTH: 0.1875 INCHES NOMINAL IN
•
CONE WIDTH: 1.9370 INCHES NOMINAL IN
TYPICAL APPLICATIONS
  • Long-term data archival and compliance retention
  • Offsite backup and disaster recovery
  • Air-gapped ransomware protection
  • Cold storage tier for infrequently accessed data
TECHNICAL CHARACTERISTICS
CUP WIDTH1.5620 INCHES NOMINAL IN
OVERALL WIDTH1.9370 INCHES NOMINAL IN
OVERALL OUTSIDE DIAMETER4.1250 INCHES NOMINAL IN
BACKFACE CORNER RADIUS0.0300 INCHES NOMINAL IN
CONE CORNER RADIUS0.0300 INCHES NOMINAL IN
STANDOUT WIDTH0.1875 INCHES NOMINAL IN
CONE WIDTH1.9370 INCHES NOMINAL IN
SPECIAL FEATURESBENCH LATERAL 0.0080 IN,SNAP RING GROOVE IN OD,HOLE IN OD FOR LOCKING PIN IN
BORE DIAMETER2.0000 INCHES NOMINAL IN
MATERIALSTEEL OVERALL
SUBSTITUTES & CROSS-REFERENCES 3
ASSY90307Reference document
Same NSN cross-reference
Reference document — Secondary reference
9-904-101368Reference document
Same NSN cross-reference
Reference document — Secondary reference
231646Reference document
Same NSN cross-reference
Reference document — Secondary reference
LIFECYCLE
NSN statusActive· U.S. Government catalog
Acquisition advice: Normally procured from the manufacturer (OEM)No demilitarization required
Ready to buy 385AX384DRBX2S385A?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is 385AX384DRBX2S385A?
385AX384DRBX2S385A is a BEARING,ROLLER,TAPERED.
What parts can replace 385AX384DRBX2S385A?
There are 3 known substitutes for 385AX384DRBX2S385A: ASSY90307, 9-904-101368, 231646. Substitute compatibility should be verified for your specific system.
What is the NSN for 385AX384DRBX2S385A?
385AX384DRBX2S385A is cataloged in the U.S. Government catalog under NSN 3110-00-119-8172. This indicates validated use in U.S. government and defense supply chains.
Community Feedback
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — 385AX384DRBX2S385A